Micro Technic Micronix 1800 Series Скачать руководство пользователя страница 18

Страница: 18 / 21

Page 18 / 21

Technical data

Power supply

Input voltage (nominal)

8 – 27Vdc.

Input voltage (MAX)

35Vdc.

Output voltage

5Vdc

External load

Up to 4A, depending on configuration and thermal

conditions.

UPS interface:

4 pins in CN7

Run/stop, AUX1,AUX2,AUX3 (factory use only).

GSM-modem:

Modem type

GM47 (SonyEricsson).

SIM card interface

3V or 5V

Frequency range

EGSM 900 MHz

1800 MHz (Dual Band).

Maximum RF output power

Antenna impedance

Antenna connector type

MMCX RF connector

Supported I/Os (using AT

commands)

Available in 10pin connector

3 Analogue inputs *

8 bit, 0 – 2.75V

1 Analogue output *

8 bit, 0 – 2.475V

4 general purpose digital inputs * 0 – 2.75V

COM ports:

Number of ports

Two, one used for GSM modem

Addressing range

2C8h, 2D8h, 2E8h, 2F8h, 3D8h, 3E8h, 3F8h, disabled

IRQs supported

3, 4, 5, 7, 9, 10, 11, 12, 15

Connector

Port 2 available in 10pin box header.

Analogue inputs:

Resolution

12 bit

Inputs

8 ch. single ended or 4 ch. differential – one common

Isolation

1kV, 1 minute

Input range configurations

(all unipolar)

8 x 0–2.5V (default) or

8 x 0-5V or

8 x 0-10V or

8 x 0-20mA or

4 x 0-20mA + 4 x 0-2.5V

Input impedance

1M (default).

Accuracy

0.5% of FSR, ±3LSB (default)

Conversion time

11us

Connector type

10 pin box header

Digital inputs:

Number of channels

8 isolated, one common ground

Digital logic levels

0 – 24V, non-polarity,

Input low voltage: 0 – 1.5V

Input high voltage: 10 – 24V

Содержание Micronix 1800 Series






















Результаты поиска

Содержание Micronix 1800 Series

Отзывы:

Похожие инструкции для Micronix 1800 Series

Бренды по названию

Популярные бренды

Micro Technic Micronix 1800 Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Micronix 1800 Series

Отзывы:

Похожие инструкции для Micronix 1800 Series

Бренды по названию

Популярные бренды