background image

Occasionally, it may be necessary to readjust various components in order to maintain optimum
performance. The adjustments that may be performed are as follows:

The cross-slide is mounted on a dovetail slide, as shown below. Between the sloping surfaces on
one side of the dovetail, a

 

ib strip

 

is inserted, which may be tightened against the dovetail under

the influence of three adjuster, or

 

ib

 

screws

,

 mounted along it

 len t .

The  ib screws are to be found on the right hand side of the slide, directly beneath the compound
slide handle. ln time, wear will occur on the mating surfaces resulting in a

 

sloppiness

 

of action.

To adjust the  ib strip, account for wear

,

 and ensure the slide moves evenly and smoothly,

proceed as follows:
1. 

Loo en

 all lock nuts and screw in the

     ib screws evenly, i.e. use the same torque
    for each screw. The slide should be held
    firmly. Test by trying to turn the handle, but
    do not force it.
2. Screw out each  ib screw by one quarter of
    a turn only, and 

nu

 up the lock nuts.

3. Test again, by turning the handle  the
    movement should be even and smooth 
    along its complete length.
4. lf the movement is too slack, screw all adjusters

 

in

 

by one eighth of a turn, and re-try.

    Similarly, if the movement is too stiff, screw

 

out

 

the adjusters by one eighth of a turn until the 

    correct adjustment is attained.
5. Tighten all lock nuts

,

 taking care to ensure you do not move the  ib screws whil

e

 doing so.

6. When completed, retract the slide fully and apply oil to all mating surfaces and the feed screw
    thread, then wind the slid

e

 back to its normal position.

The cross-slide feed should run smoothly, and the scale must rotate with the handle.
lf any stiffness occurs, it is probably the result of 

e r

 lodging between the mating surfaces.

Undo the screw securing the handwheel. Remove the handwheel and pull off the collar
with the scale

,

 taking great

  are to reta n t e 

all  pr n  plate w

  t   n a  roo e

beneath the collar.
Clean the assembly and reassemble  n reverse order. l

t

 will be necessary to hold the spring plate

in place with a small screwdriver,

 

or similar tool, 

w le 

pushing down on it to allow the collar to be

correctly located on to the shaft

.

The tailstock

   lo e

 by two screw

en

 

t e  rew  are 

loose

ne ,

 the tailstock can moved left or

 r

t.

en 

lock

e   own,

 

t e ta l to  

can 

fixed any position 

alon

 the bed

 way.

 

SETTINGS AND ADJUSTMENTS

A. CROSS-SLIDE ADJUSTMENTS

B. CROSS-SLIDE FEED HANDLE

C. TAILSTOCK ADJUSTMENTS

NOTE:
lt is important that the cross-slide and compound slide adjustments are 

a e 

correctly and that

there is no

 

sloppiness

 

of action. Any maladjustment will have a serious effect on the quality of

your work, as they will all be transferred to the tool tip. lt is vital that there is as little movement of
the tool as possible.

9

ib strip

ib or

Adjuster

Screws

Содержание MicroLux 85181

















Отзывы: