MICRO-EPSILON ILD 1320-10 Скачать руководство пользователя страница 100

Страница: 100 / 108

Page 100

Warranty

optoNCDT 1320

A 4

Control Menu

A 4.1

Tab Home

Measurement
task

Presets

Standard

Suitable for materials made of ceramics, metal or filled plastics

Multi surface

Suitable for e.g. PCB or hybrid materials

Light penetration

Suitable for plastics (POM, Teflon), materials with strong pen-
etration of the laser

Setup

Setup 1

A setup contains user-specific measurement settings. Unlike the
presets it can be changed anytime.

Signal quality

Static / balanced / dynamic

The signal quality affects averaging of measurement values.

A 4.2

Tab Settings

A 4.2.1

Inputs

Laser on/off

On / Off

Laser on/off is only effective when pin 8 is connected to GND.

Multifunctional input

Zeroing (Mastering) High / Low Sets the function of the switching input. The trigger affects

recording and output of a measurement value. Zeroing/Master-
ing sets the current measurement value to the entered master
value. Teaching scales the analog output. HTL is defined as
active input level.

Trigger In

High / Low

Teaching

Inactive

Key function

Zeroing (Mastering)

Sets the function of the sensor key. Inactive means keylock.

Teaching

Inactive

1) Available for the sensor models ILD1320-10/25/50.

Содержание ILD 1320-10













































































































Результаты поиска

Содержание ILD 1320-10

Отзывы:

Похожие инструкции для ILD 1320-10

Бренды по названию

Популярные бренды

MICRO-EPSILON ILD 1320-10, Инструкция по эксплуатации

Результаты поиска

Содержание ILD 1320-10

Отзывы:

Похожие инструкции для ILD 1320-10

Бренды по названию

Популярные бренды