background image

CA-Series Operator’s Manual   

 

 

 

 

 

 

   

 

  

3

introduction

Congratulations on the purchase of your new cold water pressure washer!  You can be assured your cold water pressure 
washer was constructed with the highest level of precision and accuracy.  Each component has been rigorously tested 
by technicians to ensure the quality, endurance and performance of this unit.  

This operator’s manual was compiled for your benefit.  By reading and following the simple safety, installation, operation, 

maintenance and troubleshooting steps described in this manual, you will receive years of trouble free operation from 
your new cold water pressure washer.  The contents of this manual are based on the latest product information available 
at the time of publication. Mi-T-M

® 

reserves the right to make changes in price, color, materials, equipment, specifications 

or models at any time without notice.

! important !

tHese paragrapHs are surrounded by a “safety alert boX”.  tHis boX is used 
to designate and empHasize safety warnings tHat must be followed wHen 
operating tHis pressure wasHer.  accompanying tHe safety warnings are 
“signal words” wHicH designate tHe degree or level of Hazard seriousness.  
tHe “signal words” used  in tHis manual are as follows:

 

DANGER

indicates an imminently Hazardous situation wHicH, if not  

 

 

 

avoided, will result in deatH or serious injury.

 
 

WARNING

indicates a potentially Hazardous situation wHicH, if not  

 

 

 

avoided, could result in  deatH or serious injury.

 
 

CAUTION

indicates a potentially Hazardous situation wHicH, if not  

 

 

 

avoided may result in minor or moderate injury.

tHe symbols set to tHe left of tHis paragrapH are “safety alert symbols”.  
tHese symbols are used to call attention to items or procedures tHat could 
be dangerous to you or otHer persons using tHis equipment.

always provide a copy of tHis manual to anyone using tHis equipment.  read 
all  instructions  before  operating  tHis  pressure  wasHer  and  especially 
point  out  tHe  “safety  warnings”  to  prevent  tHe  possibility  of  personal 
injury to tHe operator. 

Once the unit has been uncrated, immediately write in the serial number of your unit in the space provided below.

SERIAL NUMBER_________________________________

Inspect for signs of obvious or concealed freight damage. If something appears to be damaged, file a claim with the 

transportation company immediately.  Be sure that all damaged parts are replaced and that the mechanical problems 

are corrected prior to operation of the unit.  If you require service, contact a Mi-T-M Customer Service Representative 
at 800-553-9053.

Please have the following information available for all service calls:

 

 

 

 

 

Model Number

 

 

 

 

 

2. 

Serial Number

 

 

 

 

 

3. 

Date and Place of Purchase

Mi-T-M

®

 Corporation

8650 Enterprise Drive

Peosta, IA  52068-0050

Содержание CA-3304-0MHB






















Отзывы: