MHSC WEF26 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 20

MHSC WEF26 Скачать руководство пользователя страница 13

68D5001

1

•

Replacing Flame Generation LED

1. Follow Steps 1 through 4 in 'Cleaning Firebox'.
. Remove screws securing log to either side of base. Remove log.

Figure 10

.  Remove screws from sides and back of bottom panel of firebox.
4.  Gently lay unit on its back.
5.  There are several wires attached to bottom panel. Carefully

remove panel.

6.  Disconnect wires from motor and LED drum assembly.
7.  Remove screws from bottom panel to remove assembly.
8.  If motor on assembly fails, loosen clamps.

Figure 19.

Re-

move screws from motor. Hold universal joint while removing
motor and discard.

9. Install new motor. Slide motor shaft into universal joint and

tighten clamps.

10. Hold LED drum assembly in place on bottom panel and re-

place screws.

11. Reattach wires to motor and LED drum.

NOTE:

LED drum

wires are polarity sensitive and must be connected correctly.
White wire plugs onto left terminal and red wire plugs onto
right terminal. Motor wires can be connected to either termi-
nal.

1. Replace fireplace bottom panel. Set fireplace upright and

replace screws.

1. Replace log, glass and brackets.
14. Reinstall fireplace and replace trim.

FP2404
flame LED drum

White Wire

Red Wire

LED Drum
Assembly

Motor

Screws

Clamps

FP404

Figure 19

•

Cleaning or Replacing Rear Glass (Screen)

1. The glass is cleaned in the factory during assembly. During shipment, installation,

handling, etc., glass surface may collect dust particles. These can be removed by
buffing lightly with a clean damp cloth (water only). Glass should be completely
dried with a lint free cloth or paper towel.

. In the event of glass breakage, vacuum all remaining glass pieces with a shop

vac. DO NOT VACUUM WHILE PIECES ARE HOT. Replace glass only with
replacement part specifically for this heater. Never substitute material. Only fully
tempered soda lime safety glass may be used on this heater.

. To access glass to clean or replace, follow Steps 1 and 7 in 'Replacing Flame

Generation LED'. Set aside bottom panel.

4. Using gloves, gently remove glass panel by sliding it toward you. There is a rub-

ber bumper on each corner of glass.

5. Clean glass as instructed in Step 1 or replace glass.
6. Using gloves, reinstall glass by gently sliding, smooth side toward fireplace front,

into brackets on either side that hold glass in place.

7. Replace log base.
8. Follow Steps 11 and 14 in 'Replacing Flame Generation LED'.

«
...
11
12
13
14
15
...
»

Содержание WEF26





















Отзывы:

Нет отзывов