MHS Boilers EURON 24, Инструкция по установке и эксплуатации

Страница: 43 / 49

43 of 49
Service manual
Appendix
LMU (Specialist Engineer Parameters)
For Access to the next level (whilst in Parameters 516
– 727)
Keep program keys 1 ( Down Button) and 2 ( Up Button) pressed simultaneously for approx a further 5 secs. Ref page 22
Parameter Name Setting Unit Description
504 TkSmax 85 ºC
Maximum boiler setpoint temperature (>= "TkSmin" and <= 90
°C) must be at least 3 K less than for "TkMax"
505 TkS standard 80 ºC Boiler setpoint at standard outside air temperature
506 TvSmin 20 ºC
Minimum flow setpoint temperature (>= 20 °C and <=
"TvSmax")
507 TvSmax 80 ºC Maximum flow setpoint temperature ( >= TvSmin and <= 90°C)
521 dTkTrNenn 20 K
Delta T Control: flow and return at standard Outside air
Temperature (>= 2,5 K and <= maximum "dTkTrMax")
522 dTkTrMax 25 K
Delta-T-control: maximum differential of the supply/return
temperature at standard Ouside Air temperature
537 NqmodNenn 30
Speed level of boiler pump in design point of heating installation
("NqmodNenn" <= "QmodDrehzStufen")
538 NqmodMin 40 % Minimum pump speed permitted for the heating installation
541 PhzMax 100 %
Maximum modulation rate in heating mode (>= "LmodTL" and
<= "LmodVL")
551 Kon 2 Constant for rapid power fluctuation without ambient effect
552
Hydraulic
System
6 Hydraulic system adjustment
553 KonfigHks 553
Configuration of heating circuit (position YX, X for heating circuit
1, Y for heating circuit 2 of LMU...)[ Value: 0 no room unit effect,
1 heating circuit 1 of room unit, 2 heating circuit 2 of room unit]
555 KonfigRg1 0010000
Installation options for: DHW priority, installation frost
protection, modem function, {room thermostat input, timer
switch}; ({} not LMU7...)
558 KonfigRg4 1000000
Installation options for: DHW thermostat, water pressure
sensor, function changeover valve outlet {heat demand Q8,
construction} ({} not LMU7...)
561 KonfigRg7 0001000 installation options for: Pump modulation, Regulator delay
596 ZeitAufZu 135 s Operating time of mixer engine (time off / time on)
605 LPBAdrGerNr 1 LPB unit number of the LMU...
606 LPBAdrSegNr 0 LPB segment number of the LMU...
610 LmodVL_QAA 100 %
Setpoint operation: Modulation air in normal load, upper limit
modulation area
614 KonfigEingang 1
Installation options (function) of programmable input of the
LMU...-Base
615 Konfigoutlet 0
Installation options (function) of relay outlet K2 of the LMU...-
Base
618 KonfigEingangR 0
Installation options (function) of programmable input of relay
ClipIn
619 Konfigoutlet1R 0001010 Installation options function) of relay outlet 1 of the relay ClipIn
620 Konfigoutlet2R 0000001 Installation options (function) of relay outlet 2 of the relay ClipIn
For Access to the OEM level: Access Specialist Engineer Parameters as detailed above
Keep program keys 1 (
Down Button) and 2 ( Up Button) pressed simultaneously for approx 10 secs.
When asked for OEM code, Password = 1 ( Down Button), 2 ( Up Button), 4 ( Plus Button), 3 ( Minus Button), 4 ( Plus Button)