MGL Avionics V16 Скачать руководство пользователя страница 8

Страница: 8 / 13

the procedures required.
No acknowledge is sent in response to these commands

Increase Intercom volume (3dB).

Don't care data value (recommend to set to zero)

Sends acknowledge when message received OK

Decrease intercom volume (3dB).

Don't care data value (recommend to set to zero)

Sends acknowledge when message received OK

Set Intercom volume

Volume value 0-31 (lowest to highest)

Sends acknowledge when message received OK

Increase RX volume (3dB).

Don't care data value (recommend to set to zero)

Sends acknowledge when message received OK

Decrease RX volume (3dB).

Don't care data value (recommend to set to zero)

Sends acknowledge when message received OK

Set RX volume

Volume value 0-31 (lowest to highest)

Sends acknowledge when message received OK

Format of Acknowledge message (sent by transceiver)

$02 $05 $06 $53 (full message including checksum)

Format of status message (sent by transceiver every 100mS unless setup

menu is active)

STX

DLE

Message type

Flags
Bit 0 – 1 = TX is active
Bit 1 – 1 = Scanning is active

Содержание V16














Результаты поиска

Содержание V16

Отзывы:

Бренды по названию

Популярные бренды

MGL Avionics V16, Руководство пользователя

Результаты поиска

Содержание V16

Отзывы:

Бренды по названию

Популярные бренды