MGL Avionics V16 Скачать руководство пользователя страница 6

Страница: 6 / 13

Note: Frequency must be a valid frequency. Invalid frequencies will be ignored and no
acknowledge will be sent for the message.

Sends acknowledge when message received OK

Increase RX and Intercom volume (3dB), If they are different they will be set to
the same value as the intercom volume.

Don't care data value (recommend to set to zero)

Sends acknowledge when message received OK

Decrease RX and IC volume (3dB), If they are different they will be set to
the same value as the intercom volume.

Don't care data value (recommend to set to zero)

Sends acknowledge when message received OK

Set RX and Intercom volume

Volume value 0-31 (lowest to highest)

Sends acknowledge when message received OK

Increase squelch

Don't care data value (recommend to set to zero)

Sends acknowledge when message received OK

Decrease squelch

Don't care data value (recommend to set to zero)

Sends acknowledge when message received OK

Set squelch

Squelch value 0-31 (lowest to highest)

Sends acknowledge when message received OK

Set scanning on/off

0 = scanning off
1 = scanning on

Sends acknowledge when message received OK

Playback request

Don't care data value (recommend to set to zero)

Note: If this message is received while playback of last RX is not active, it will activate

Содержание V16














Результаты поиска

Содержание V16

Отзывы:

Бренды по названию

Популярные бренды

MGL Avionics V16, Руководство пользователя

Результаты поиска

Содержание V16

Отзывы:

Бренды по названию

Популярные бренды