manualshive.com logo in svg

MGL Avionics Stratomaster Maxi Single Flight II, Руководство пользователя, Страница: 20 / 23

Поделиться
Скачать
MGL Avionics Stratomaster Maxi Single Flight II Скачать руководство пользователя страница 20

 

Installing the Flight II 

 
 

Alarm lamp
Suggested rating: 1W
also usable is a LED if
used with suitable dropping 
resistor

Red

Black

Fuse

Power
switch

Positive supply
(+12V from battery)

Negative supply
(airframe ground)

Suggested fuse rating:
1.0 A slow blow

To other instruments

Cannon D-9

connector

Fuel level

sender

Ambient

temperature

sender

Fuel flow sender

Red wire 
from flow senders

Blue wire 
from flow
sender

Braid from 
flow sender

Brown

Yellow

Green

Red

Blue

Orange

Green

Cannon D-9 connector
pin mapping and cable colors

1 - ground - Black
2 - fuel level - Orange
3 - ambient temperature - Green
4 - not used
5 - Engine RPM - Blue
6 - power (+12V) - Red
7 - power out for fuel flow - Brown
8 - fuel flow signal - Yellow
9 - alarm output -White 

White

Pin 1

Pin 5

Pin 6

Pin 9

Terminal strip (not supplied)

Reference ground
to engine block

Ground

Breaker

Ignition
coil

2K2 resistor

20Volt
zener diode

 

Содержание Stratomaster Maxi Single Flight II
























Отзывы:

Нет отзывов