MGG HT-023 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 15

MGG HT-023 Скачать руководство пользователя страница 10

10

Step 10: Final placement of the boundary wire and training flags

Once you have made adjustments to the signal field width and completed the manual
tests  on  the  entire  system  to  your  satisfaction,  you  can  bury  the  boundary  wire.
Burying the wire is not essential but for wire-protection you probably want to bury it at
least  2-3cms deep.   Alternatively,  you can mount  the wire onto a wooden rail fence
but not in a position that birds can sit on the wire and damage it.

NB:  If you are covering a large area you may wish to use a trenching machine to cut
into  the  ground.    However,  we  recommend  that  you  manually  place  the  boundary
wire into the trench to avoid any damage to the wire.

Tools required



Straight-edged spade



Wire cutters

Additional items you may need if you are running the boundary wire beneath
concrete driveways or paths



Caulk gun



Silicone caulking

When crossing a concrete path or driveway, use the existing expansion joints.  Clean
out  the  joint  thoroughly.    Lay  the  wire  carefully  into  the  open  seam  and  seal  with  a
bead of silicone caulking or similar sealant.

When crossing gravel, bury the boundary wire at least 7cms deep.

Lengths  of  old  garden  hose  or  similar  PVC  piping  are  useful  protection  to  the
boundary wire, particularly in areas such as gravel and ponds.

Manual retest and setting the boundary training flags

Once  the  boundary  wire  is  fully  installed,  MANUALLY  re-test  the  entire  system  and
adjust the signal field-width as per steps 8 and 9.

When you are verifying the system, place the boundary training flags where you hear
the first warning beep on your approach to the boundary wire.   The flags should be
placed  along  the  edge  of  the  signal  field  width,  not  directly  on  the  boundary  wire.
This  will  provide  a  visual  clue  with  the  audio  warning  tone  to  help  your  dog  learn
where the perimeter of the containment area is during training sessions.

When you are satisfied the system is fully functioning to your settings and the
boundary flags are in place then you are ready to move onto Section 2:
Training your dog with the MGG Radio-Controlled Hidden Fencing System

«
...
8
9
10
11
12
...
»

Содержание HT-023
















Отзывы:

Нет отзывов