MFJ MFJ-185, Инструкция по эксплуатации

Страница: 2 / 3

Button Functions in Normal Time Mode:
DATE/TEMP – Toggles upper left display between temperature and day of the week
12/24
°
C /
°
F – When the upper left part of the LCD displays temperature, this button toggles the
display between
°
C and
°
F. When the upper left part of the LCD displays the day of the week, this
button toggles the time display between 12 Hr and 24 Hr format.
SET – Briefly pressing the SET button will illuminate the E.L. Backlight for about 3 seconds.
When the upper left part of the LCD displays temperature, pressing and holding the SET button
will adjust the temperature down 3
°
C and a hand icon will appear on the LCD by the temperature.
This is for body temperature adjustment. When the upper left part of the LCD displays the day of
the week, pressing and holding the SET button will initiate the Time Setting Mode.
Notes about Temperature:
•
When the watch is worn on the wrist, your body temperature will affect the temperature
reading and the accuracy will decrease.
•
When the ambient temperature changes rapidly, the MFJ-185 may take up to 30 minutes to
achieve an accurate reading.
•
For the most accurate temperature reading, remove the watch from your wrist and place it in
the environment to be measured.
•
Do not expose the temperature to direct sunlight. Exposure to direct sunlight can cause the
temperature to read higher than the actual temperature and not be accurate.
Time Setting Mode
Follow these steps for Setting the MFJ-185:
•
Be sure you are in Normal Time Display Mode and the Day of the week appears in the upper
left corner of the LCD.
•
Press the SET button and hold for a few seconds until the seconds digits begin to flash.
•
Press the DATE/TEMP button to reset the seconds to “00”.
•
Press the MODE button and the hour digits will begin to flash.
•
Press the DATE/TEMP button to advance the hour.
•
Press the MODE button and the minutes digits will begin to flash.
•
Press the DATE/TEMP button to advance the minutes.
•
Press the MODE button and the year digits will begin to flash.
•
Press the DATE/TEMP button to advance the year.
•
Press the MODE button and the month digits will begin to flash.
•
Press the DATE/TEMP button to advance the month.
•
Press the MODE button and the date digits will begin to flash.
•
Press the DATE/TEMP button to advance the date.
•
To continue in the Time Setting Mode, pressing the MODE button will cycle through the
settings.
•
To exit the Time Setting Mode, pressing the SET button briefly and the LCD will return to
the Normal Time Mode.
WORLD TIME MODE
In Normal Time Mode, press the MODE button once to enter World Time Mode. In the World
Time Mode, the city abbreviation will be displayed in the upper left corner of the LCD. The time
in that city will be disp layed in the upper right corner of the LCD. The country code & area code,
high temperature, or low temperature will be displayed below the world map. Please see the table
below for city abbreviations:
Abbr. City Abbr. City Abbr. City Abbr. City
AKL Auckland CPH Copenhagen LON London SFO San Francisco
AMS Amsterdam CPT Cape Town LUX Luxembourg SHA Shanghai
ATH Athens DUB Dublin MEL Melbourne SIN Singapore
BCN Barcelona DXB Dubai MEX Mexico STO Stockholm
BER Berlin FRA Frankfurt MNL Manila SYD Sydney
BJS Beijing HEL Helsinki MOW Moscow TPE Taipei
BKK Bangkok HKG Hong Kong NYC New York City TYO Tokyo
BOM Bombay HNL Honolulu OSL Oslo VIE Vienna
BRU Brussels JER Jerusalem P A R Pairs YTO Toronto
BUE Buenos Aires JKT Jakarta RIO Rio De Janeiro YVR Vancouver
CAI Cairo LAX Los Angeles ROM Rome ZRH Zurich
CAS Casablanca LIM Lima SCL Santiago
CHI Chicago LIS Lisbon SEL Seoul
Button Functions in World Time Mode:
DATE/TEMP – When the Country Code and Area Code are displayed below the world map, this
button will cycle through the 50 cities in alphabetical order. When the typical high or low
temperature is displayed below the world map, this button will cycle through the typical
temperatures for each month of the year. The month for which the temperatur e is displayed is
located in the lower right corner next to the temperature.
12/24
°
C /
°
F – When the Country Code and Area Code are displayed below the world map, this
button will let you adjust the time of the city displayed if Daylight Savings Time is observed. DST
will appear in the upper right corner buy the city time when enabled. When the high or low
temperature is displayed below the world map, this button will toggle between the typical high and
low temperature for the month displayed.
SET – Briefly pressing the SET button will illuminate the E.L. Backlight for about 3 seconds and
toggle between the typical temperature information and County Code and Area Code information.
Pressing and holding the SET button will allow you to adjust the time of the city displayed.
World Time Setting Mode
Please note that although you may have correctly set the time in Normal Time Mode, the time
displayed in the World Time Mode may not be correct. You must set the time in the World Time
Mode to match the time in Normal Time Mode. Follow these steps to ensure the world time and
normal time match:
1.
In World Time Mode, cycle through the cities until you come to a city in your time zone.
2. Be sure that the Country Code and Area Code information is displayed below the world map.
If it is not briefly press the SET button.
3. With the Country Code and Area Code information displayed below the world map, press and
hold the SET button until the hour digits flash in the upper right corner.
4. Press the DATE/TEMP button to adjust the hour to the current hour in your time zone.
5. Press the MODE button and the minutes will begin to flash.
6. Press the DATE/TEMP button to adjust the minutes to the current time in your time zone.
7. Press the SET button briefly to exit the World Time Setting Mode.
ALARM TIME MODE
In Normal Time Mode, press the MODE button twice to enter Alarm Time Mode. In World Time
Mode press the MODE button once to enter the Alarm Time Mode. In Alarm Time Mode, “AL”
will appear in the upper left corner above the world map and the actual time will appear in the
upper right corner above the world map. The alarm time will appear below the world map. To set
the alarm time, follow these steps:
1.
Press and hold the SET button until the hour digits of the alarm time begin to flash.
2. Press the DATE/TEMP button to adjust the hour.
3. Press the MODE button and the minutes digits will begin to flash.