MFJ Legas Limit IntelliTuner MFJ-998 Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 52

background image

MFJ-998 Legal Limit IntelliTuner Automatic Antenna Tuner

Instruction Manual

©

2007-2010 MFJ Enterprises, Inc.

27

•

Beep On

•

Refresh Off

•

Radio Interface

Off

•

Push Tune <0.5s

To Bypass

† These settings are stored separately for antennas 1 and 2.

Note: Resetting to factory defaults does not erase the antenna memories.

To reset the tuner to these defaults:

1.

Turn off the power to the tuner.

2.

Press and hold

both

the [TUNE] and [L-UP] buttons while turning the power on.

3.

Release the buttons when

DEFAULTS RESET

appears on the display.

4.

Resume normal operation.

WARNING:

If the MFJ-998 is not behaving properly or is acting erratically, try resetting the
tuner to factory defaults.

Disable Radio Interface

If the wrong radio interface is selected and the

TURN ON RADIO

message does not go away, disable the

interface by pressing and holding

both

[TUNE] and [MODE] buttons while turning the power on. The

tuner will respond with two beeps. Then enter the setup mode to select the correct radio interface.

Delete Entire Antenna Memory

To delete an entire antenna memory (all four banks), select Antenna 1 or Antenna 2 with the [ANT]
button that you want to delete. Turn off power to the tuner, and then press and hold

both

the [TUNE] and

[ANT] buttons while turning the power back on. A confirmation message

DELETE ANTENNA

will

display. Press the YES [C-DN] button to delete the antenna memory (a progress bar and

DELETED

will

display), or press the NO [L-DN] button to cancel (

CANCEL

will display). Release the button to resume

normal operation. Remember that the selected antenna memory will be lost!

Delete Antenna Memory Bank

To delete an antenna memory bank, select Antenna 1 or Antenna 2 and the antenna memory bank with the
[ANT] button that you want to delete. Turn off power to the tuner, and then press and hold

both

the

[TUNE] and [C-UP] buttons while turning the power back on. A confirmation message

DELETE BANK

will display. Press the YES [C-DN] button to delete the antenna memory (a progress bar and

DELETED

will display), or press the NO [L-DN] button to cancel

(

CANCEL

will display). Release the button to

resume normal operation. Remember that the selected antenna memory bank will be lost!

Total Reset

To erase

both

antenna memories and reset to factory defaults, press and hold down the [TUNE], [C-UP]

and [L-UP] buttons while turning the power on. A confirmation message

TOTAL RESET

will display.

Press the YES [C-DN] button to delete both antenna memories and reset factory defaults (a progress bar
and

RESET

will display), or press the NO [L-DN] button to cancel (

CANCEL

will display). Release the

button to resume normal operation. Remember that both antenna memories will be lost!

«
...
31
32
33
34
35
...
»

Содержание Legas Limit IntelliTuner MFJ-998





















































Отзывы:

Нет отзывов

Похожие инструкции для Legas Limit IntelliTuner MFJ-998

Бренд: Boss Audio Systems Страницы: 9

Бренд: Harman Kardon Страницы: 12

Бренд: GE Страницы: 6

Spacemaker 7-4235

Бренд: GE Страницы: 12

Бренд: GE Страницы: 52

Бренд: Bosch Страницы: 16

Бренд: Bosch Страницы: 33

GoAllTV SMARTSTICK

Бренд: EasyPlay Страницы: 12

AutoTuner Extender MFJ-914

Бренд: MFJ Страницы: 2

Бренд: AVer Страницы: 16

Бренд: MFJ Страницы: 9

Бренд: UbiTech Страницы: 18

Бренд: ZeeVee Страницы: 32

Бренд: ZENEC Страницы: 24

Бренд: Newhank Страницы: 4

Бренд: Panasonic Страницы: 32

Бренд: Extron electronics Страницы: 118

Бренд: ADS Technologies Страницы: 1

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды