MFJ IntelliTuner -994B Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 48

background image

MFJ-994B IntelliTuner Automatic Antenna Tuner

Instruction Manual

©

2004-2010 MFJ Enterprises, Inc.

3

Fast Start

WARNINGS

●

Never operate the tuner with its cover removed. Contact with the components inside the
tuner while transmitting will result in painful RF burns.

●

Locate the tuner so that the rear terminals are not accessible during operation. The single
wire connection may have high voltage while transmitting.

●

Disconnect all antennas from the tuner during lightning storms.

●

Always tune with low power (2-20 watts), and with any in-line amplifier bypassed. Apply
maximum power only after tuning up.

●

Never exceed tuner specifications.

1. Connect the tuner to a 12-15 VDC voltage source capable of supplying at least 850 milliamps.

2. Connect your transmitter or amplifier output to the TRANSMITTER connector using a 50-ohm

coaxial cable.

3. Connect your coax-fed antenna to the ANTENNA connector using a 50-ohm coaxial cable, or

connect your random wire to the WIRE binding post.

4. Connect your ground connection to the GROUND post.

5. Press the [POWER] button to turn on the MFJ-994B tuner.

6. Lock the [AUTO] button in to select semi-automatic mode.

Note: The AUTO button should always be IN (semi-automatic) unless a compatible radio

interface cable is connected between the MFJ-994B and your transceiver. This ensures
that the MFJ-994B does not attempt tuning during high-power operation, and is
particularly important when an HF amplifier is in-line.

Note: If an amplifier is in-line, it should always be bypassed prior to tuning.

7. Key your transmitter to output a carrier of 2-20 watts CW, FM or AM.

Note: Due to detector non-linearities at low power levels, best SWR tuning accuracy occurs at

10-20 watts.

8. Press and hold the [TUNE] button for one second to start the automatic tuning process. When

completed, check to ensure an SWR of 1.5 or less has been achieved before increasing RF power.

Note: If you have a tuning solution on one band or antenna and you then change bands or

antenna and attempt to transmit a tuning signal, the previous tuning solution may be
sufficiently severe such that no power is detected by the MFJ-994B (the MFJ-994B will
tell you to increase power). When this occurs, simply bypass the MFJ-994B and then
initiate a tune.

Note:

If the tuner was unable to achieve the target SWR, the Reflected Power needle will
bounce three times when tuning completes.

9. You are ready to transmit with full power.

Note: During the automatic tuning process, the tuner will make some noise. These are the

relays switching at a very high rate and this is normal. Do not be alarmed.

«
...
7
8
9
10
11
...
»

Содержание IntelliTuner -994B

















































Отзывы:

Нет отзывов

Похожие инструкции для IntelliTuner -994B

Professional DN-U100

Бренд: Denon Страницы: 24

SmartStream PC2TV

Бренд: Wonder Media Страницы: 73

Бренд: GE Страницы: 6

Spacemaker 7-4235

Бренд: GE Страницы: 12

Бренд: GE Страницы: 52

Бренд: Kenwood Страницы: 12

Бренд: Kenwood Страницы: 16

Бренд: Kenwood Страницы: 22

Бренд: Kenwood Страницы: 12

Бренд: Kenwood Страницы: 12

Бренд: Kenwood Страницы: 12

Бренд: Kenwood Страницы: 19

Бренд: Kenwood Страницы: 20

Бренд: Kenwood Страницы: 17

Бренд: Kenwood Страницы: 22

Бренд: Kenwood Страницы: 17

Бренд: Kenwood Страницы: 23

Бренд: Kenwood Страницы: 88

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды