MFJ IntelliTuner -994B Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 48

background image

MFJ-994B IntelliTuner Automatic Antenna Tuner

Instruction Manual

©

2004-2010 MFJ Enterprises, Inc.

33

Yaesu Radio Interface/MFJ-5124Y3

The MFJ-5124Y3 radio interface allows users of Yaesu FT-1000MP series, FT-2000 series, and FT

DX

-

9000 series transceivers to connect to the MFJ-994B

IntelliTuner™

Automatic Antenna Tuner. With this

interface, control signals are connected between the radio and the tuner. With this cable the operator can
control the tuner and radio with a single push of the [TUNE] button on the front panel of the MFJ-994B.

Connections for FT-1000MP series of radios

1. Before connecting the MFJ-5124Y3 to your radio, set the maximum TUNE power of the radio as

follows:

a. On your transceiver, enter the Menu mode by pressing and holding the [FAST] key and then

pressing [ENT].

b. Rotate the [MEM/VFO CH] knob until you see menu 4-3 on the transceiver’s CH display.

c. Rotate the [MAIN VFO] knob to select 50 for 100-watt radios (FT-1000MP/MP Field) or 75

for the FT-1000MP MKV when an amplifier will be used. This gives the best SWR
accuracy, which may be important for solid-state amplifiers. When an amplifier is not used,
the setting can be set at 10 for all transceivers.

d. Press [ENT] to exit the Menu mode.

2. Insert the 3.5 mm stereo phone plug into the MFJ-994B RADIO INTERFACE jack.

3. Connect the 3.5 mm mono plug on the MFJ-5124Y3 to the REMOTE jack on the rear panel of

the transceiver.

4. Connect a 12V 1000 mA DC source to the MFJ-994B.

5. Push the [POWER] button on the MFJ-994B to the

in

position. The radio may be powered on

either before or after the tuner is powered on.

Operation for FT-1000MP series of radios

The transceiver is controlled by the MFJ-994B. To operate:

1. Press the [TUNE] button on the MFJ-994B for ½-2 seconds to initiate the tuning process. The

radio will automatically transmit a low-power carrier and start the tuning process. When tuning is
completed, the radio will stop transmitting and you will be ready for operation on this frequency.

Connections for FT-2000 series of radios

1. Before connecting the MFJ-5124Y3 to your radio, set the maximum TUNE power of the radio as

follows:

a. On your transceiver, enter the Menu mode by pressing the [MENU] key momentarily.

b. Rotate the Main Tuning Dial knob until you see menu item [145 tGEn TUN PWR] on the

transceiver’s display.

c. Rotate the [SUB VFO-B] knob to select 20 watts for best SWR accuracy. For the FT-2000D,

we recommend that this be set to 50 watts if the user normally operates at 100 watts output
power (when power is turned down to 100 watts, the TUNE power will reduce to 25 watts).

«
...
37
38
39
40
41
...
»

Содержание IntelliTuner -994B

















































Отзывы:

Нет отзывов

Похожие инструкции для IntelliTuner -994B

Бренд: SCT Страницы: 20

Бренд: Onkyo Страницы: 32

Бренд: Meisel Страницы: 2

Бренд: Vimar Страницы: 6

Бренд: HANDAN Страницы: 40

BURGcam REC 351

Бренд: BURG WATCHER Страницы: 32

CONTERPOINT II FM 100

Бренд: Harman Kardon Страницы: 4

Бренд: Videostrong Страницы: 10

Бренд: TechniSat Страницы: 56

Бренд: eversense Страницы: 20

Бренд: Alinco Страницы: 12

Бренд: Alinco Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды