MFJ IntelliTuner -991B Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 48

background image

MFJ-991B IntelliTuner Automatic Antenna Tuner

Instruction Manual



2005-2012 MFJ Enterprises, Inc.

35

Yaesu Radio Interface/MFJ-5124Y4

The MFJ-5124Y4 radio interface allows users of Yaesu FT-2000 series and FT

DX

-5000 series

transceivers to connect to the MFJ-991B

IntelliTuner™

Automatic Antenna Tuner. With this interface,

control signals are connected between the radio and the tuner. The operator can then control the tuner and
radio with a single push of the [TUNE] button on the front panel of the MFJ-991B.

Connections for FT-2000 series of radios

1.

Before connecting the MFJ-5124Y4 to your radio, set the maximum TUNE power of the radio as
follows:

a. On your transceiver, enter the Menu mode by pressing the [MENU] key momentarily.

b. Rotate the Main Tuning Dial knob until you see menu item [145 tGEn TUN PWR] on the

transceiver’s display.

c. Rotate the [SUB VFO-B] knob to select 20 watts for best SWR accuracy. For the FT-2000D,

we recommend that this be set to 50 watts if the user normally operates at 100 watts output
power (when power is turned down to 100 watts, the TUNE power will reduce to 25 watts).
If the operator normally has his FT-2000D set for the full 200 watts, then this should be set to
20 watts.

d. Press and hold in the [MENU] key for two seconds to save the new setting and exit to normal

operation. If you press the [MENU] key momentarily, the new setting will

not

be saved.

2.

Insert the 3.5 mm stereo phone plug into the MFJ-991B RADIO INTERFACE jack.

3.

Connect the RCA plug on the MFJ-5124Y4 to the TX REQ jack on the rear panel of the
transceiver.

4.

Connect a 12V 1000 mA DC source to the MFJ-991B.

5.

Push the [POWER] button on the MFJ-991B to the

in

position. The radio may be powered on

either before or after the tuner is powered on.

Operation for FT-2000 series of radios

The transceiver is controlled by the MFJ-991B. To operate:

1. Press the [TUNE] button on the MFJ-991B for ½-2 seconds to initiate the tuning process. The

radio will automatically transmit a low-power carrier and start the tuning process. When tuning is
completed, the radio will stop transmitting and you will be ready for operation on this frequency.

«
...
39
40
41
42
43
...
»

Содержание IntelliTuner -991B

















































Отзывы:

Нет отзывов

Похожие инструкции для IntelliTuner -991B

Бренд: Samson Страницы: 2

Бренд: Palstar Страницы: 8

AX2000 Contact AutoTuner

Бренд: SABINE Страницы: 2

Бренд: Pentek Страницы: 14

Бренд: Motorola Страницы: 48

Бренд: Moon Audio Страницы: 13

Бренд: IconBiT Страницы: 17

Бренд: Royale Страницы: 8

Бренд: NAD Страницы: 16

Бренд: NAD Страницы: 15

AM/FM Radio Tuner

Бренд: Xantech Страницы: 13

Бренд: Yamaha Страницы: 8

Бренд: Palstar Страницы: 8

Бренд: Fender Страницы: 2

Бренд: TC Electronic Страницы: 7

Rocktile CMT-600C

Бренд: Kirstein Страницы: 2

Бренд: Hauppauge Страницы: 2

Бренд: Technics Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды