MFJ IntelliTuner -991B Скачать руководство пользователя страница 12

Страница: 12 / 48

MFJ-991B IntelliTuner Automatic Antenna Tuner

Instruction Manual



2005-2012 MFJ Enterprises, Inc.

BUTTON ACTION

TUNE

C-UP

L-UP

TUNE

L-DN

TUNE

C-DN

L-DN

C-UP

C-DN

Press + to switch the capacitor between the input and output side.

Press + to bypass the antenna tuner.

Press + to cycle the Auto Tune SWR among 0.5, 1.0 and 1.5 above the target SWR.

Press + to toggle the Target SWR between 1.5 and 2.0.

Press + to cycle the Memory among banks A, B, C and D.

Press + to cycle the Meter Range among 30 watts, 300 watts and auto range.

Press + to increase both capacitance and inductance.

C-UP

L-UP

AUTO

C-UP

L-UP

C-DN

L-DN

TUNE

POWER

Press in to select semi-automatic mode, out to select automatic mode.

Press to decrease inductance.

Press to increase inductance.

Press to decrease capacitance.

Press to increase capacitance.

Press in to turn power on, out to turn power off.

Press less than 0.5 second to bypass the tuner; press and hold for 0.5 to 2 seconds to start the

tuning process; press and hold for more than two seconds to toggle the StickyTune on and off.

Press +

to overwrite tuner memory with the current tuner setting.

TUNE

L-DN

C-DN

Press +

toggle the power level between 300 and 150 watts.

TUNE

C-UP

L-UP

Figure 3. Button Action.

Содержание IntelliTuner -991B

















































Результаты поиска

Содержание IntelliTuner -991B

Отзывы:

Похожие инструкции для IntelliTuner -991B

Бренды по названию

Популярные бренды

MFJ IntelliTuner -991B, Инструкция по эксплуатации

Результаты поиска

Содержание IntelliTuner -991B

Отзывы:

Похожие инструкции для IntelliTuner -991B

Бренды по названию

Популярные бренды