background image

Disclaimer

MFB does not assume any liability for completeness or accuracy for
any of the pages in this manual. We reserve the right to change any
of the terms and contents at any time without advance notice. The
content of this manual has been compiled with meticulous care and
to   our   best   knowledge.   MFB   does   not   take   responsibility   for   any
warranties  for  this  manual   beside   the  ones  being  defined   by  the
corresponding commercial laws.
Any duplication, processing or form of distribution of this manual or
parts of it requires permission of the manufacturer.

Safety Instructions

Please carefully read the following safety instructions! These include
general rules of handling electric products. Carefully read all notes
before operating the unit.

Suitable place of installation

Only use this device in confined spaces, avoid humidity and dust.

Ensure unhindered airflow to all sides of the device. Do not place

the device in direct proximity to heat sources.

Do not expose the device to direct sunlight or strong vibrations.

Electrical connection

Please only use the power supply that comes with the device. It
can be used with a supply voltage of 110 to 240 volts (mains).

If the provided  power supply does not suit  your power socket,
please consult a qualified electrician.

Unplug the power supply if you are not going to use the device
for a longer period.

Never touch the power supply with wet hands.

While unplugging, always pull the plug not the cable!

3

Содержание SYNTH Pro

























Отзывы: