background image

PWM

----------------------------------
Activate pulse width modulation by setting OSC 2’s waveform to impulse. A modulation 

will no longer target this oscillator’s pitch but its symmetry for timbral changes.

Glide

----------------------------------
Press  GLIDE  to   activate   the   Portamento/Glide   function,   a   step   less   pitch   transition 

between  two  adjacent played  notes.  The control sets the  speed in which  the pitch 
moves from the old to the new note position.

User memory

----------------------------------

The 

LITE II

 has 83+83 User sound memory locations. To call up the memories press and 

hold  USER  followed  by a  combination of the six  buttons to the left of the module. 

Pressing   just   one   of   these   buttons   will   call   up   memory   locations   01-06.   Press   two 
adjacent knobs. (11....16, 21....26,... 61...66) to access the memories up to 41.

An additional 42 memory locations can be accessed by pressing GLIDE button upfront the 

described procedure. The display will always inform you about the selected location.
Finally you can adress another 83 memory locations by switching the 

LITE II 

off and on 

while pressing  WAVEFORM  in the  LFO  section. The display indicates the memory bank 
with a dot.

Important:  

Location 01 is no memory location. It calls up the sound by the current 

setting of all knobs and controls (manual mode).

To save a sound into a memory location press RECORD. Then press and hold USER and 
chose the memory location just as described above. Copying sounds is done in the same 

way.

Setting the MIDI channel

----------------------------------
To set the MIDI channel, press  RECORD. Then press  WAVEFORM  (LFO) to increase the 

channel number up to 16 and then starting back from 1 again. Confirm channel selection 
with RECORD.

Pitch Wheel

----------------------------------

Incoming  pitch   wheel  data   will  result   in   global  pitch  modulation  of  plus   minus  two 
semitones.

Modulation Wheel

----------------------------------

The Mod Wheel can either control the  VCF  (cutoff) or the  VCOs  (pitch), depending on 
the system settings.

 

Содержание SYNTH LITE II









Отзывы: