14
PUSH MODE
The POWER PRIMUS II can also be swit-
ched to push mode.
The electronic wheelchair has a consi-
derably higher weight than conventional
wheelchairs (motor, batteries). This me-
ans that higher pushing and steering for-
ce are necessary.
Note!
Only push
the wheelchair on level
surfaces.
The electromagnetic brake is switched
from drive to push mode by way of the
brake release lever on the side of the
wheelchair!
The brake release lever on the side of
the wheelchair is used to switch the elec-
tromagnetic brake from drive mode to
push mode!
– Controlled braking is
not possible!
Handling:
1. Switch off the wheelchair.
Press the I/O button (17) on the control
box.
2. Push mode
First pull the knob on the brake release
lever, then push the brake release lever
backwards. (Fig. 35).
Drive mode
Push the brake release lever forward,
(Fig. 36).
FOLDING/UNFOLDING
POWER PRIMUS II is also collapsible for
car transportation (Fig. 37).
FOLDING THE WHEELCHAIR
1. Switch off the wheelchair. – Switch
off the wheelchair with the I/O but-
ton (17) on the control box, (Fig.
38). The battery control display goes
off.
Note:
If the wheelchair has a seat width of
43 cm or less, remove the side parts
before folding and replace them after
unfolding.
Folding up the seat
2) Fold up the seat to the right (Fig. 39).
– To carry this out, lift the seat up out
of the seat tube (Fig. 40).
Removing the batteries:
3 Disconnect the battery plug (A) (Fig.
41).
4) Open the lock on the elasticated belt
(Fig. 42) – by pressing down the
spring release mechanism.
5) Lift out the front battery box (Fig. 43).
6) Lift out the back battery box (Fig.
44).
SEAT BELT
The seat (4) can be folded up to enable
better access to the battery holder (fol-
ding/unfolding the wheelchair) (Fig.
31).
Folding up the seat
Lift up the left seat mounting strip out of
the seat tube.
Inserting the seat
Press the fixing pins on the seat down
into the appropriate holes on the moun-
ting strip, which is located on the seat
frame, as far as they will go (Fig. 32).
Note:
To simplify the process of inserting the
stabiliser rod, lift it up or press it down
at the centre (Fig. 33).
The seat should fit flush to the tube
after mounting
(Fig.34).
– Press down the stabiliser bar at the
centre as far as it will go
Содержание 2.432
