manualshive.com logo in svg

Meyer Utility Plow, Руководство владельца и руководство пользователя

Поделиться
Скачать
Meyer Utility Plow Скачать руководство пользователя страница 19

Grease

Grease

POST-SEASON SUMMER MAINTENANCE

1. Draining & Replacing Meyer Utility Plow Meyer M-1 Hydraulic 
Fluid 

Drain the fl uid by un-bolting the hydraulic unit from the Lift Frame and 

removing the Reservoir Breather. Turn the hydraulic unit upside down and drain 
the fl uid from the reservoir. To drain the fl uid from the power angling cylinders(if 
equipped), disconnect the fi ttings and completely retract the cylinder rods 
and purge cylinder and hose of all hydraulic fl uid. The complete system should 
then be fl ushed out with Meyer M-2 Flushing Fluid before adding new Meyer 
Hydraulic Fluid. To fl ush the unit, re-install the hydraulic unit to the Lift Frame 
and hose to the angle cylinder (if equipped).  Add 1 quart of M-2 Flushing Fluid 
to the reservoir and replace the Reservoir Breather. Cycle the unit Up, Down, Left 
and Right 5 times in each direction. Then drain the hydraulic unit as before and 
re-fi ll with Meyer M-1 Fluid. Check fl uid level after cycling plow and top off  if 
necessary.

2. Meyer M-1 Hydraulic Fluid

 

is specially formulated with an anti-ice additive 

for almost constant viscosity in subzero temperatures. Because it is free-fl owing in 
extreme cold, the unit’s performance and effi  ciency are not aff ected by winter weather. 
It is eff ective for a maximum of one year. Always carry an extra quart of 

Meyer M-1 

Hydraulic Fluid

. Use of any inferior fl uids will void the Meyer Products warranty.

SNOW PLOW STORAGE

1. 

When snow plow is disconnected, 

disconnect lift chain from lift arm 

and extend lift cylinder to end of stroke and coat chrome rod with light 
grease. 

This fi lls the cylinder with hydraulic fl uid and protects the interior and 

exterior from rust and corrosion.

2. 

Whenever Moldboard is disconnected, coat the exposed portions of the power 

angling cylinder chrome rod (if equipped) with light grease to protect it from corrosion.

3. 

Coat pivot pin and other wear points with chassis lubricant. Be sure to grease all 

grease holes.

4. 

Unplug electical connection. Coat connection with a dielectric compound to 

prevent corrosion and plug into their corresponding weather plug.

Yellow and black paint is formulated 
to withstand harsh temperatures and 
the winter environment.

Protects your electrical system 
with Meyer winter formula 
dielectric grease.

Meyer M1 Hydraulic oil  and Flush is 
scientifi cally formulated to withstand 
extreme winter temps up to -40F.

Dielectric Grease

Available at www.meyerproducts.com

17

24, 30

7, 9, 12, 13, 15, 16, 17, 19, 20, 21

SAFETY PRECAUTIONS - 

See pages 2-3 for defi nitions

Содержание Utility Plow





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды