manualshive.com logo in svg

Meyer Utility Plow, Руководство владельца и руководство пользователя

Поделиться
Скачать
Meyer Utility Plow Скачать руководство пользователя страница 18

Meyer Products recommends this maintenance information for regular service. Sustained heavy operation may call for more frequent service. Snow plowing 
subjects a vehicle to exceptionally rugged use. As a result, it is very important to inspect and maintain the snow plow and vehicle up to maximum operating conditions. 

Inspection should be made of both the vehicle and snow plow prior to the plowing season and after each use.

PRE-SEASON MAINTENANCE 

Scheduled vehicle maintenance should be performed as recommended by the manufacturer.

VEHICLE ELECTRICAL SYSTEM 

For maximum effi  ciency, the vehicle supporting the snow plow must be properly serviced. The system should 

consist of at least a 70 amp./hr. battery and a 60 amp alternator. Be sure to check regularly:
 

1. Battery terminals to assure they’re clean and free of corrosion.

 

2. Electrical connections, to assure they’re tight and corrosion free.

 

3. Battery must be in top operating condition.

 

4. Alternator and regulator, to assure maximum electrical output.

Check the Diagnosis chart Pre/Post Season Maintenance for advice on maintaining the unit.

1. ALWAYS LOWER MOLDBOARD TO THE GROUND WHEN SNOW PLOW IS BEING SERVICED OR WHEN 
VEHICLE IS NOT IN USE

.

2. 

Check and maintain hydraulic fl uid reservoir level to Full. Oil level should be checked with lift ram down or retracted position.

3. 

Check entire hydraulic system for leaks. A signifi cant drop in hydraulic fl uid level is evidence of a leak which must be corrected to prevent serious damage.

4. 

Before and after each season, Grease all pins and lubricate all pivot points with chassis lube.

5. CUTTING EDGE – 

Replace the cutting edge as soon as it is 3-1/2” (5” is new) Tall. This will prevent permanent damage to the moldboard (fi g. 43).

6. ADJUSTING TRIP SPRING TENSION – 

Tighten top locknut 4 turns beyond the point when spring coils begin to separate. Tighten bottom locknut to 

hold eye bolt in position (fi g. 44).

7. MOUNTING BOLTS – 

Retighten all mounting bolts after fi rst snow plowing session and at regular intervals through the season.

8. SNO-FLO® POWDER COATING

, both black and yellow, should be checked at the beginning and end of each season for any signs of rust. 

If any exists, use Sno-Flo® powder coat touch-up available in spray cans.

NOTE: PROTECTION AGAINST RUST AND CORROSION 

When the power unit is not used for extended periods, 

protect the chromed 

lift rod by fully extending and coating it with chassis lubricant. 

Coat the exposed portions of the power angling cylinder rods with chassis 

lubricant to protect against corrosion.

Pre-season & Post-season Maintenance

(Fig. 43)

(Fig. 44)

16

Cutting Edge

Trip Spring Adjustment

24, 30

4, 7, 9, 12, 13, 15, 16, 17, 19, 20, 21

SAFETY PRECAUTIONS - 

See pages 2-3 for defi nitions

Содержание Utility Plow





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды