Meyer STELLA-188 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 28

Meyer STELLA-188 Скачать руководство пользователя страница 20

CHAPTER 3: STELLA MOUNTING OPTIONS

20

MOUNTING THE STELLA-8C

The Stella-8C can be mounted flush in ceilings and walls
with any standard 8-inch backbox (such as the Atlas
BMT95-8-7, Lowell CP-87 or XCP-87) with a minimum
depth of 6.5 inches.

Installing the Stella-8C in a Backbox

To install the Stella-8C in a standard 8-inch backbox:

1. Mount the backbox in the ceiling or wall according the

manufacturer's instructions.

2. Place the Stella-8C in the backbox and secure it with the

8-32 screws included with the Stella-8C.

3. Attach the Stella-8C grille frame:

■

Screw the three threaded studs (included with the
Stella-8C) into the Stella-8C grille frame.

■

Attach the grille frame to the Stella-8C by inserting the
other ends of threaded studs into the three nylon latches
in the Stella-8C.

■

Gently push the grille frame in until it locks in place flush
with the wall or ceiling.

NOTE:

The Stella-8C’s grille frame is held in

place with three nylon latches. To remove the

grille frame, gently pull it, evenly, until it releases from
the latches.

Stella-8C Mounted in Third-Party Backbox

Backbox

Stella-8C
grille frame

Stella-8C

«
...
18
19
20
21
22
...
»

Содержание STELLA-188





























Отзывы:

Нет отзывов