manualshive.com logo in svg

Meyer Sound Stella-188, Руководство по эксплуатации

Поделиться
Скачать
Meyer Sound Stella-188 Скачать руководство пользователя страница 25

STELLA OPERATING INSTRUCTIONS

25

STELLA-8C SPECIFICATIONS

Operating Frequency Range

100 Hz – 18 kHz

Note:

 Recommended maximum operating frequency range. Response depends on loading conditions and 

room acoustics.

Frequency Response

115 Hz – 16 kHz ±4 dB

Note:

 Measured free-field with pink noise at 1 meter, 1/3rd octave resolution.

Maximum Peak SPL

117 dB

Note:

 Measured free-field with music and referred to 1 meter.

Phase Response

2 kHz – 18 kHz ±45°

Coverage

100°

Transducer

One 8” coaxial cone driver; one 0.75” metal dome tweeter

Voltage Requirement

12–18 V DC

Audio/Power Connector

Single 5-pin Phoenix (3 pins for balanced audio, 2 pins for DC power)

Input Impedance

20 k

 balanced internal isolation (Iso-Input) transformer

Nominal Input Sensitivity

+6 dBV (2.0 V rms, 2.8 V peak) continuous average is typically the onset of limiting for noise and music

Input Level

Audio source must be capable of deli15 dBV (5.6 V rms, 8.0 V peak) into 600 

 to produce the 

maximum peak SPL over the loudspeaker’s operating bandwidth

Current Draw

3.1 A average; 6.3 A peak

Noise Floor

<20 dB A weighted

Dimensions

11.66” (front OD) x 5.47” (depth without grille)
296.16 mm (front OD) x 138.86 mm (depth without grille)

Weight

9.0 lbs (4.1 kg) without backbox

Stella-8C Dimensions

Ø13.23

 [Ø336.02mm]

11.25

 [285.75mm]

7.95

 [202.06mm]

Ø0.22

 [Ø5.50mm]

8.72

 [221.49mm]

6.29

 [159.83mm]

1.40

 [35.56mm]

5.47

 [138.86mm]

11.66

 [296.16mm]

Содержание Stella-188

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды