Metso Neles N1 Series Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 36

background image

6 N1 70 en

19

4.5

Actuator Reassembly

4.5.1

General reassembly

Remove and discard all old seals and gaskets.

Parts should be cleaned to remove all dirt and other foreign
material prior to inspection.

Parts should be thoroughly inspected for excessive wear,
stress cracking, galling and pitting. Attention should be
directed to threads, sealing surfaces and areas that will be
subjected to sliding or rotating motion. Sealing surfaces of
the cylinder, tie bars and piston rod must be free of deep
scratches, pitting, corrosion and blistering or flaking coating.

Before installation apply film of lubricant on all moving
parts. Apply film of lubricant on all seals before installing
into seal grooves.

For Spring Module Installation refer chapter 4.3 section
4.3.2.

4.5.2

Central block module reassembly

Step 1.

Install bottom yoke bearing (46) in central block

housing (11). Apply grease on bearing seat on central block
housing for ease of assembly.

Step 2.

Install carrier (15) in yoke (13) then insert yoke pin

assembly (16) with roller (17) and washer (18) from bottom
side for carrier.

Step 3.

Install hex. Head cap screw in carrier to locate the

yoke pin at the center of carrier.

Step 4.

Install top side roller (17), washer (18) and retaining

ring (49) on yoke pin (16).

CAUTION:

Only new seals, which are still within the seal’s expectant
shelf life, should be installed into the actuator being refur-
bished.

CAUTION:

Actuator parts that reflect any of the above listed charac-
teristics should be replaced with new parts.

NOTE:

Parts and seals used in the actuator will be assembled
using lubricant as identified in unit 1 section 1.8.

NOTE:

Review unit 4.5 - section 4.5.1 General Re-assembly before
proceeding with central block Module reassembly.

NOTE:

Lubricate yoke pin (16), roller (17) and carrier (15).

«
...
17
18
19
20
21
...
»

Содержание Neles N1 Series





































Отзывы:

Нет отзывов

Похожие инструкции для Neles N1 Series

Бренд: Zolix Instruments Страницы: 22

SolarCell Remote

Бренд: Samsung Страницы: 2

Бренд: Samsung Страницы: 20

FUTERA XLF Series

Бренд: RBI Страницы: 128

Бренд: RBH Access Technologies Страницы: 36

Бренд: S&C Страницы: 11

Бренд: S&C Страницы: 24

Бренд: S&C Страницы: 19

IntelliZone2 MasterStat

Бренд: Water Furnace Страницы: 44

MusicCAST MCX-CA15

Бренд: Yamaha Страницы: 176

Бренд: D+H Страницы: 32

Бренд: Casambi Страницы: 2

Бренд: Paser Страницы: 2

Бренд: Computer Automation Technology Страницы: 55

Бренд: micro-trak Страницы: 44

Бренд: Rain Bird Страницы: 48

Бренд: Sullair Страницы: 31

ESP32-C3 Series

Бренд: Espressif Systems Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды