4
III. CleanIng InsTRUCTIons
CAUTION
AT NO TIME SHOULD THE MODULE OR
CABINET BE WASHED OR FLOODED WITH
WATER OR LIQUID SOLUTION. NEVER
STEAM CLEAN. SEVERE DAMAGE OR
ELECTRICAL HAZARD COULD RESULT.
. turn off power switch.
2. unplug the unit from its power source.
WARNING
ALLOW THE UNIT TO COOL BEFORE
CLEANING, AS THE INTERIOR OF THE
CABINET MAY BE HOT ENOUGH TO BURN.
A. SHELF REMOVAL/INSTALLATION
to remove the shelves, all shelves must first
be lowered onto the bottom shelf. Start with
the shelf above the bottom shelf by lifting it off
of the shelf hangers and by lowering the front
edge and raising the rear edge so that it can
be lowered onto the bottom shelf. Repeat the
procedure until all of the shelves are on the
stack on the bottom shelf.
on double door cabinets, lift the uppermost
shelf off of the stack so that you are holding
onto the long edge of the shelf and the shelf
is hanging vertically. Position the shelf so one
vertical edge is in one of the rear cabinet
corners. Swing the other vertical edge out the
door and remove the shelf. Repeat until all the
shelves are removed.
on single door cabinets, lift each shelf off of
the stack so that you are holding onto the long
edge of the shelf and the shelf is hanging
vertically. Position the shelf so that one vertical
edge is in one of the rear cabinet corners and
the other vertical edge is towards the diagonal
front corner. Depending on the model of the
one door cabinet, the shelf may have to be
rotated towards a vertical position to remove it
from the cabinet.
to install the shelves, reverse the above
procedure. Before installing the shelves
install the module (Section B below) and, if so
equipped, the Quad-Heat Fuel System baffle(s)
and chimney(s) (Section c below).
NOTE:
the shelf wires that run from left to right
in the cabinet should be on the top side of the
installed shelves. Make sure the shelves are
seated in the hangers correctly.
on single door MBQ-90 and 72 cabinets, the
shelves have two 90° square corners and two
45° notched corners. the 45° corners go to the
right end as you look into the cabinet.
B. ELECTRIC HEATING MODULE
REMOVAL/INSTALLATION
. Remove the module from the cabinet by
lifting and sliding the module rearward. Lift
the front of the module and stand it vertically
C. COUNT-UP/COUNT-DOWN TIMER/CLOCK
CLOCK MODE
. Press the Mode button until the clock icon
appears on screen next to the printed
“cLocK” icon.
2. Press and hold (Set) for two seconds.
3. “HouRS” will flash.
4. Press (
▲
) or (
▼
) to set.
5. Repeat process to set minutes or seconds.
6. to complete the process press (Set).
NOTE:
the two-second delay is to prevent
accidental changing of time. there is no
delay in timer mode.
COUNT-DOWN TIMER MODE
can be used to countdown the minutes until the
canned fuel needs to be replenished.
. Press the Mode button until the timer icon
appears on the screen next to the printed
“tiMeR” icon.
2. Press (Set).
3. “HouRS” will flash.
4. Press (
▲
) or (
▼
) to set up or down to desired
interval (23:59:59 max.).
5. Repeat process to set minutes or seconds.
6. Press (StaRt) to start. Press (StoP) to stop.
HELPFUL HINTS:
• if you want to set only hours, it is not
necessary to press (Set) through minutes
and seconds. Simply set desired interval and
press (StaRt).
• as a reminder, your timer will “beep” for 3
seconds when it reaches 5 minutes before
set interval expires.
• When timer reaches 00:00:00 the alarm will
sound and “tiMe’S uP!” will appear on the
screen. Your timer will now begin to count
up. the alarm will stop after 60 seconds and
your timer will continue to count up until you
press (StoP).
• (cLeaR) button can be used at any time
to clear the display. (cLeaR) button also
functions for recall of last setting.
• (RecaLL) feature: after you press (StoP),
pressing the (RecaLL) button will
automatically display the last timer setting.
• each time you press (
▲
) or (
▼
) the
digits will change once. if you hold the button
down digits will change rapidly.
COUNT-UP TIMER MODE
can be used to track how long food has been in
the cabinet.
. Press the Mode button until the stop watch
icon appears on screen next to the printed
“StoP WatcH” icon.
2. Press (StaRt) to start. Press (StoP) to stop.
