background image

2

IMO-270EN

Table of Contents

1

GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.1

Warning  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

2

INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

3

MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
3.1

Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

3.2

Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

4

SERVICE KITS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

5

REPAIR KITS/SPARE PARTS . . . . . . . . . . . . . . . . . . . . 6

READ THESE INSTRUCTIONS FIRST!

This instruction manual contains important information regarding the installation, operation, and troubleshooting
of the Jamesbury® Series 7000 8" (DN 200) Class 150 Standard Bore, Series 9000 2" – 6" (DN 50 – 150) Class 150  and
2" – 4" (DN 50 – 100) Class 300 Full Bore Valves.  Please read these instructions carefully and save them for future
reference.

SAVE THESE INSTRUCTIONS!

Subject to change without notice.

Содержание Jamesbury 7000 Series







Отзывы: