background image

Chapter II 

28  

Portable digital multimeter 

5.3. DC 

current 

 

Selector 

switch 

Accuracy 

Max. voltage 

drop 

Protection 

Fuses 

 

Resolution 

5 mA 

1 µA 

50 mA 

700 mV 

10 µA 

500 mA 

0.2 % R + 2 D 

1.5 V 

F1 + F2 

100 µA 

10 A

∗∗

 

0.5 % R + 5 D 

500 mV 

600 V

RMS

 

F2

10 

mA

∗ 

refer to fuse specifications section 6.1.1. 

∗∗ 

acceptance overload: 20 A during 30 s. max. observing a break > 5 min between 2 tests  

Number of count :  5000  
Additional error in Pk +/- mode for a pulse width of 

 1 ms : 1 % R 

±

 50 D 

For  measurements performed on alternative signals, the selected range must tally with the max. 
value of the signal peak. 

5.4. 

AC currents (AC and AC + DC) 

 

Accuracy 

40 Hz to  

5 kHz 

5 kHz to 

20 kHz 

20 kHz 

to 30kHz

Ranges 

5 % to 100 % of range 

Protect. 

Fuses

 

Resol. 

Max. 

Crest 

Max. 

voltage 

drop  

5 mA 

1%R+3D 

1.5% typ. 4% typ.

1 µA 

10 mA

50 mA 

1.5% typ. 4% typ.

10 µA 

100 mA

700 mV 

500 mA 

1%R +3 D 

1.5% typ. 4% typ.

F1 + F2

100 µA 

1 A 

1.5 V 

10 A

∗∗

 

1.5%R+3 D 

Æ

 2 kHz 

1.5% typ.

/////////// 

600  

V

RMS

 

F2 

10 mA 

30 A 

500 mV 

 refer to fuse specifications section 6.1.1. 

∗∗ 

acceptance overload: 20 A during 30 s. max. observing a break > 5 min between 2 tests  

Specification : 

from 5 % to 100 % of the range 

Number of count : 

5000 

Additional error according to crest factor :  

0 %  for a crest factor < 1.5 
1 %  for a crest factor of 1.5 to 2 
4 %  for a crest factor of 2 to 3 

Additional error in I

AC+DC

 with a direct current at input : 1 % 

5.5. 

Resistance / Continuity 

  

Ranges

Accuracy

Measur. 

current 

Protection

 

Resolution 

500

 Ω/

0.1% R + 5 D 

1 mA 

100 m

Ω

 

5

 

k

Ω 

100 µA 

Ω

 

50 k

Ω 

10 µA 

10

 Ω

 

500 k

Ω 

0.1% R + 3 D 

1 µA 

100 

Ω

 

5 M

Ω∗∗ 

0.3% R + 3 D 

100 nA 

1k 

Ω

 

50 M

Ω∗∗ 

1% R + 3 D 

50 nA 

600 V

RMS

 

10 k

 Ω

 

 Overload protection can be reset automatically. 

∗∗ 

The use of very short and shielded test leads is highly recommended for measurements in 

this range (> 1 M

Ω

).  

Number of count : 

5000 

Range selection : 

automatic or manual (set in continuity mode) 

Maximum open circuit voltage : 

7 V 

Detection threshold in continuity mode : 

10 

Ω

 to 20

 Ω

 

Response time in continuity mode : 

1 ms 

Содержание MX 58HD




















Отзывы: