background image

99-6543HG

9

Installing the interface

It is highly advisable to read the following steps beforehand, to ensure a clear understanding of 

what is to be expected. The following steps must be done in the order that they are numbered.

With the vehicle completely off:

Touchscreen display
1.

  Connect the 

16-pin harness with stripped leads

 into port “B” in the touchscreen display.

2.

  Connect the 

6543 harness

 to the wiring harnesses in the vehicle. Then insert the 

6543 

harness

 into port “A” in the touchscreen display. But do not install this harness until exactly 

before step 1 of “Initializing the Interface”. This is a timed process

3.

  Connect the 

4-pin harness with yellow RCA jacks

 into port “C” in the touchscreen display.

4.

  Connect the 

hazard harness

 into port “D” in the touchscreen display, and then to the wiring 

harness in the vehicle.

 

(Make sure this is the 8-pin connector that was disconnected from 

the HVAC portion, there is the same connector that is disconnected from the touchscreen. 

Plugging in the wrong plug will cause a jam on the CANBUS.)

5.

  Disregard port “E”, it will not be used in this application.

6.

  Port “F” is an update port for future firmware upgrades.

7.

  Locate the factory antenna connector in the dash and complete all necessary connections 

to the radio. Metra recommends using the proper mating adapter from Metra.

A

B

C

E

F

D

Initializing the interface

Attention! 

If the interface loses power for any reason, the following steps  

will need to be performed again.

1.

  Refer to step 2 of “Installing the interface”.

2.

  Press the push-to-start button to start the vehicle.

3.

  Program the kit:

 

a.

  Once the touchscreen display loads up, select the vehicle type; “Pacifica 2017-up”.

 

b.

  Wait until the radio comes on, and the touchscreen display shows  

   “SWC Configured”. This process may take up to 3 minutes.

 

Note:

 If the touchscreen display does not load up, or the radio doesn’t come on within 3 

minutes, and/or the touchscreen display does not show “SWC Configured”, turn the vehicle 

off and disconnect the 

6543 harnesses

 from port “A” in the touchscreen display. Check all 

the connections, reconnect the harness into the touchscreen display, and then try again. 

4.

  Test all functions of the installation for proper operation, before reassembling the dash.

 Note:

 The clock and compass in the driver’s information center will no longer be functional.

Final assembly

1.

  Secure the completed assembly into the upper dash using the factory hardware. 

2.

  Reassemble the center console and dash in reverse order of disassembly.

Содержание 99-6543HG

















Отзывы: