Metra Electronics 99-5722 Скачать руководство пользователя

Страница: 9 / 16

INST99-5722

CONNECTIONS TO BE MADE

Attention!

This interface will work with models that are either amplified or non-amplified.

Please follow the instructions carefully for your model vehicle. Failure to do so will result in
either no sound, or low sound. If you are unsure if your vehicle is factory amplified or not, please
contact your local dealership.

For models

without

an amplifier:

From the 16-pin harness with stripped leads to the aftermarket radio:

• Connect the

Red

wire to the accessory wire.

• If the aftermarket radio has an illumination wire, connect the

Orange/White

wire to it.

•

If the aftermarket radio has a mute wire, and the vehicle is equipped with SYNC, connect the

Brown

wire to it. If the mute wire is not connected, the radio will turn off when SYNC is activated

• Connect the

Gray

wire to the right front positive speaker output.

• Connect the

Gray/Black

wire to the right front negative speaker output.

• Connect the

White

wire to the left front positive speaker output.

• Connect the

White/Black

wire to the left front negative speaker output.

The following (3) wires are only for multimedia/navigation radios that require these wires.

• Connect the

Blue/Pink

wire to the VSS/speed sense wire.

• Connect the

Green/Purple

wire to the reverse wire.

• Connect the

Light Green

wire to the parking brake wire

• Tape off and disregard the following (4) wires, they will not be used in this application:

Green

Green/Black

Purple

Purple/Black

From the 5722 harness to the aftermarket radio:

• Connect the

Black

wire to the ground wire.

• Connect the

Yellow

wire to the battery wire.

• Connect the

Blue

wire to the power antenna wire.

• Connect the

Green

wire to the left rear positive speaker output.

• Connect the

Green/Black

wire to the left rear negative speaker output.

• Connect the

Purple

wire to the right rear positive speaker output.

• Connect the

Purple/Black

wire to the right rear negative output.

• Tape off and disregard the following (1) wire, it will not be used in this application:

Blue/White

with a red connector

• For models with SYNC: Connect the

Red

and

White

RCA jacks labeled “RSE/SYNC/SAT”,

to the audio AUX-IN jacks.

• For models without SYNC: Connect the

Red

and

White

RCA jacks labeled “FROM 3.5”,

to the audio AUX-IN jacks.

• Disregard the DIN jack, it will not be used in this application.
• If equipped with factory subwoofer, connect the

White

RCA jack labeled “SUBWOOFER”,

to the subwoofer out jack.

• Disregard the

Red

RCA jack labeled “CENTER CHANNEL”, it will not be used in this application.

Содержание 99-5722

















Результаты поиска

Содержание 99-5722

Отзывы:

Похожие инструкции для 99-5722

Бренды по названию

Популярные бренды

Metra Electronics 99-5722, Руководство по установке

Результаты поиска

Содержание 99-5722

Отзывы:

Похожие инструкции для 99-5722

Бренды по названию

Популярные бренды