background image

®

6

Connections to be made 

From the 3010S-LC harness to the aftermarket radio:

• Connect the 

Black

 wire to the ground wire.

• Connect the 

Yellow

 wire to the battery wire.

• Connect the 

Red

 wire to the accessory wire.

• Connect the 

Pink

 wire to the 

Pink

 wire located in the HVAC harness

(ignore the writing on this wire, this is NOT a “mute” wire).

• Connect the 

Blue/White

 wire to the power antenna wire.

• If the aftermarket radio has an illumination wire, connect the 

Orange/White

 wire to it.

• Connect the 

White

 wire to the left front positive speaker output.

• Connect the 

White/Black

 wire to the left front negative speaker output.

• Connect the 

Gray

 wire to the right front positive speaker output.

• Connect the 

Gray/Black

 wire to the right front negative speaker output.

• Connect the 

Green

 wire to the left rear positive speaker output.

• Connect the 

Green/Black

 wire to the left rear negative speaker output.

• Connect the 

Purple

 wire to the right rear positive speaker output.

• Connect the 

Purple/Black

 wire to the right rear negative speaker output.

The following (3) wires are only for multimedia/navigation radios that require these wires.

• Connect the 

Blue/Pink

 wire to the VSS/speed sense wire.

• Connect the 

Green/Purple

 wire to the reverse wire.

• Connect the 

Light Green

 wire to the parking brake wire.

Installing the Axxess interface

With the key in the off position: 

• Connect the 3010S-LC harness into the interface, and then to the wiring harness

in the vehicle.

Initializing the Axxess interface

Attention: 

If the Axxess interface loses power for any reason, 

the following steps will need to be performed again.

• Turn the key (or push-to-start button) to the ignition position and wait until the

radio comes on.

Note: 

If the radio does not come on within 60 seconds, turn the key to the off

position, disconnect the interface, check all connections, reconnect the interface, 
and then try again.

• Turn the key to the off position, and then start the vehicle.
• Cycle the A/C fan speed all the way to high, and then back to low.
• Test all functions of the installation for proper operation, before reassembling the dash.

Axxess interface installation 99-3010S-LC

Содержание 99-3010S-LC








Отзывы: