background image

11

17.4.2014    Rev.: 3.3

METOS WATER DISPENSER

7. Troubleshooting

In case the appliance does not function as expected, review the following list of problems to fi nd out if 
the appliance can be put in order without a service call. In this way you can avoid unnecessary service 
calls and costs. In all enquiries, please contact the nearest Metos service. Most problems can be mana-
ged on the phone.

POBLEM

POSSIBLE CAUSE

ACTION

No water comes out of
the faucet

Water line obstructed (faucet is 
closed)

Open the faucet

Not enough water in the tank

Check and fi ll

Too little water coming

Filter  (option)  clogged  (water 
fl ow gradually decreases)

Replace the fi lter

Water fl ow adjusted to a too low 
fl ow rate

Adjust the fl ow rate correctly

Too much water coming

Water fl ow wrongly adjusted

Adjust the fl ow rate correctly.

Water is warm

Power cable is not properly plug-
ged in the socket

Put the cable properly in the 
socket

Defective fuse

Replace the fuse

Condenser covered by dust

Clean the condenser

Defective thermostat

Call the service

Defective compressor

Call the service

The cooler is installed in a too 
warm environmet or otherwice 
not suitable location

Call the service

The appliance does not contain parts that can be serviced by the user. Service must be carried out by an 
authorised service company.

STOP

Содержание PROFF D-I WD





















Отзывы: