|
25
EDITION 001 2001
METOS PROXY ELECTRIC FRYERS
JOINING APPLIANCES TOGETHER IN LINE
• Place the appliances side by side and adjust the tops to the
same height.
• Unite the appliances using the special unionjoint-coverings
supplied upon request
11. CONNECTIONS
The position and dimensions of connections are given in the
installation diagram at the start of this manual.
ELECTRICAL CONNECTIONS
Check that the appliance is designed to operate at the volt-
age and frequency of the power supply present on site.
Check the details given on the appliance data plate.
If used, the symbol
indicates:
CAUTION - HAZARDOUS VOLTAGE.
• Install an adequately rated omnipolar circuit-breaker upline
of the appliance in an easily accessible point, in compliance
with installation regulations; the circuit breaker must guaran-
tee immediate omnipolar disconnection from the mains, with
a minimum contact opening that allows complete disconnec-
tion in overvoltage category III conditions. The maximum per-
mitted current dispersion is 1mA/kW.
• For electrical connection, use a rubber-sheathed
fl
exible
cable which is oil resistant, type H05RN-F or H07RN-F, for
cable size consult the technical data table.
• Connect the power supply cable to the terminal board as
shown in the wiring diagram supplied with the appliance.
• Secure the power supply cable with the cable clamp.
• Protect the power supply cable on the outside of the appli-
ance with a rigid plastic or metal pipe.
• If the power supply cable is damaged, it must be replaced
by the manufacturer or the technical after-sales service or,
in any case, by a suitably quali
fi
ed technician, so as to avoid
any risk whatsoever.
PROTECTIVE EARTH AND EARTH BONDING CONNEC-
TIONS
Connect the appliance to an e
ffi
cient ground circuit. Connect
the earth conductor to the terminal with the symbol
lo-
cated next to the main terminal board.
Connect the metal structure of the appliance to the equipoten-
tial node. Connect the conductor to the terminal with the sym-
bol
on the outside part of the bottom.
This symbol indicates that the appliance must be included in
an equipotential system connected in compliance with current
regulations.
13. COMMISSIONING
See Chapter “ INSTRUCTIONS FOR MAINTENANCE”.
Instructions for installation
REMINDERS FOR THE INSTALLER
The manufacturer will not be liable for any damage or in-
jury resulting from failure to observe the following rules.
• Read this manual carefully. It provides important information
for safe installation, use and maintenance of the appliance.
• Installation, conversion to a di
ff
erent type of gas and appli-
ance maintenance must be carried out by quali
fi
ed techni-
cians authorized by the manufacturer, in compliance with
current safety standards and the instructions given in this
manual.
• Identify the speci
fi
c appliance model. The model number is
detailed on the packaging and on the appliance data plate.
• The appliance must be installed in a well-ventilated room.
• Do not obstruct any air vents or drains present on the appli-
ance.
• Do not tamper with appliance components.
6. REFERENCE STANDARDS AND LAWS
Install the appliance in compliance with current safety regula-
tions.
Install the appliance in compliance with current regulations.
7. HANDLING
• The packaging is marked with warning symbols that indicate
the precautions to be taken when handling the appliance
to avoid damage.The appliance must only be handledus-
ing suitable equipment. If lifting equipment is used, such as
forklift trucks or similar, make sure that the appliance is in a
stable position .
8. UNPACKING
Check the state of the packaging and in the event of damage,
ask the delivery person to inspect the goods.
• Remove the packaging.
• Remove the protective
fi
lm from the exterior and interior pan-
els. Use a suitable solvent to remove any residual adhesive
from the panels.
9. POSITIONING
• The overall dimensions of the appliance and the position of
connections are given on the installation diagram at the start
of this manual.
• The appliance can be installed singly or in combination with
other appliances in the same product range.
• The appliance is not suitable for integrated installation.
• Position the appliance at least 10 cm from adjacent walls.
This distance can be reduced in the presence of non-com-
bustible walls or heat-insulated walls.
• Level the appliance by means of the height-adjustable feet.
• The countertop appliance weighing less than 40kg, where
installed singly, must be secured using the
fl
anged feet pro-
vided.
APPLIANCE ASSEMBLY WITH BASE
Follow the instructions provided with the type of support uti-
lized.
Содержание 74EFRM
Страница 28: ...www metos com...