background image

i

TABLE OF CONTENTS

1. Introduction

 .............................................................................................. 1

2. Operation

 ................................................................................................... 2

2.1 Installation ................................................................................................ 2
2.2  Drilling With the TEROS 06 Auger ............................................................... 4
2.3 Connecting ................................................................................................. 4

2.3.1  Connect to METER Data Logger ........................................................ 5
2.3.2  Connect to a Non-METER Data Logger ............................................. 6

2.4 Communication ......................................................................................... 8
2.5  Removing the Sensor ................................................................................. 9

3. System

 ....................................................................................................... 10

3.1 Specifications .......................................................................................... 10
3.2 Components ............................................................................................ 13

4. Service

 ....................................................................................................... 14

4.1 Calibration ............................................................................................... 14
4.2 Maintenance ............................................................................................ 14
4.3 Troubleshooting ....................................................................................... 14
4.4  Customer Support.................................................................................... 15
4.5  Terms and Conditions .............................................................................. 15

Index

 ................................................................................................................. 16

18408-00

8.31.2020

Содержание TEROS 06



















Отзывы: