background image

SECTION 4 — FIRST AID MEASURES 

SECTION 5 — FIRE FIGHTING MEASURES 

Flammable  

No 

Means of Extinction   

In case of fire in the surroundings, use appropriate extinguishing media.

 

 

Flashpoint (°C) and 
Method  

Not applicable 

Upper Flammable Limit (% by 
volume)  

Not Available  

Lower Flammable Limit (% by 
volume)  

Not Available 

Autoignition 
Temperature (°C)  

Not Applicable  

Explosion Data — Sensitivity to 
Impact  

Not Applicable 

Explosion Data — Sensitivity to 
Static Discharge

 Not Applicable 

Hazardous Combustion Products  

Non-combustible liquid. Will not burn, or support  
combustion. Incompatible with oxidising agents, rective metals zinc and bare steel, strong

 

reducing agents, 

fluorine, bases, metals, metal oxides, metal alloys, strong bases, sulfur  
trioxide, phosphorous pentoxide, and sources of ignition. Fumes produced when heated to  
decomposition may include corrosive phosphorous oxides. This product transforms to  
pyrophosphoric acid at 200'C. 

NFPA 

(estimated) Health: 3; Flammability: 0; Instability: 0 

SECTION 6 — ACCIDENTAL RELEASE MEASURES  

Leak and Spill Procedures

 

 

General Information

 

Use proper personal protective equipment as indicated in Section 8. 

 

Spills/Leaks 

Absorb spill with inert material (e.g. vermiculite, sand or earth), then place in suitable container. Avoid 
runoff into storm sewers and ditches which lead to waterways. Clean up spills immediately, observing 
precautions in the Protective Equipment section. Provide ventilation. Spill may be carefully neutralized 
with lime (calcium oxide, CaO).

 

SECTION 7 — HANDLING AND STORAGE  

Handling Procedures and Equipment 

Wash thoroughly after handling. Remove contaminated clothing and wash before reuse. Do not get in eyes, 
on skin, or on clothing. Keep container tightly closed. Do not ingest or inhale. Use with adequate 
ventilation. Discard contaminated shoes.  

Storage Requirements 

Keep container closed when not in use. Store in a tightly closed container. Store in a cool, dry, well-
ventilated area away from incompatible substances. Keep away from metals. Do not store in metal 
containers. Store protected from moisture. Store away from alkalis.

 

 

Eye Contact 

In case of contact, immediately flush eyes with plenty of water for a t least 15 minutes. Get medical aid 
immediately. 

Skin Contact 

In case of contact, immediately flush skin with plenty of water for at least 15 minutes while removing 
contaminated clothing and shoes. Get medical aid immediately. Wash clothing before reuse.  

Ingestion 

If swallowed, do NOT induce vomiting. Get medical aid immediately. If victim is fully conscious, give a 
cupful of water. Never give anything by mouth to an unconscious person. 

Inhalation 

If inhaled, remove to fresh air. If not breathing, give artificial respiration. If breathing is difficult, give 
oxygen. Get medical aid. 

Содержание EASYKleen Pro S-10
























Отзывы: