Metal-Fach GRAND PELLET 100 Скачать руководство пользователя страница 24

Страница: 24 / 60

METAL-FACH

Heating Technology

Boiler installation

(User | Installer)

An important element of installation is the correct positioning and levelling of the GRAND PELLET type boiler, the

boilers do not require special foundations. Boiler leveling is facilitated by adjustable feet (for boilers up to

50kW). The boiler must stand vertically.

Use a spirit level to level the boiler with the ground.

Use a spirit level to align the boiler.

NOTE!

An improperly leveled boiler can be damaged.

NOTE!

It is not permissible to place the boiler in a damp or wet room as this accelerates the

corrosion phenomenon, leading in a short time to the destruction of the boiler.

The boiler should be placed on a heat insulating non-flammable base, which on each side of the boiler should

be larger than the base of the boiler by 2 cm. If the boiler is located in a cellar, it is recommended that it is

placed on a foundation of at least 5 cm. The strength of the foundation as well as the fire protection conditions

are key guidelines when placing the boiler in the right location, these include:

●

20 cm safety distance from flammable materials,

●

40 cm for flammable materials of flammability grade C3,

●

40 cm if flammability is not known.

Flammability of building masses and products

Building materials and products

A - Non-flammable

Sandstone, concrete, bricks, fireproof plaster, mortar,
ceramic tiles, granite

B - Hard to burn

Wood and cement boards, fibreglass, mineral
insulation

C1 - Hard to burn

Beech wood, oak wood, plywood

C2 - Medium flammability

Pine, larch and spruce cork, sawn wood planks, rubber
floor coverings

C3 - Readily combustible

Asphalt plywood, celluloid, polyurethane, polystyrene,
polyethylene, plastic, PVC

Содержание GRAND PELLET 100





























































Результаты поиска

Содержание GRAND PELLET 100

Отзывы:

Бренды по названию

Популярные бренды

Metal-Fach GRAND PELLET 100, Техническая и эксплуатационная документация

Результаты поиска

Содержание GRAND PELLET 100

Отзывы:

Бренды по названию

Популярные бренды