Mesko MS 4080, Руководство пользователя

Страница: 4 / 76

4
22. Change the accessories only when the device is switched off. Disconnect the device
from the power.
17. In order to avoid injuries handle the blades carefully.
Don't use aggressive detergents to clean the housing, as it may remove the informational
graphic symbols such as: scale, signs, safety marks, etc.
16. Do not insert fingers or any other objects into blender's cup when the blender is on.
19. For safety reasons use only original accessories and spare parts intended for particular
blender type, available at authorised service centre.
20. Handle the blades with extreme care while disassembling accessories. The blades can
cause cuts.
18. Watch out for long hair, scarves, neckties hanging above the cup and operating
components of device.
25. Do not start the empty mixing cup, without product inside.
23. Do not put any products other than food and liquids in the blender cup. Do not put hot
products in the cup.
26. MAXIMUM PERIOD OF CONTINUOUS BLENDER OPERATION IS 2 MINUTES. After
2 minutes of continuous operation stop the device and wait couple of minutes before
restarting.
24. The device is not suitable for whipping egg whites, kneading dough or grinding meat.
21. Do not wash any blender parts in dishwashers.
b) crush ice, if you want to crush ice, the quantity of ice in glass jug should be about 10 pieces, and size of the ice cube should not be
more than 30*23*23mm.
ASSEMBLY / DISASSEMBLY
1. Place the jug upside down on a flat, stable surface. Place the plastic round ring (10) below the glass thread of the jug, then place the
gasket (4) over the glass thread, then position the blade (5). Then put the plastic nut (6) on all parts placed before and turn it clockwise
until all parts are screwed tightly (photo 3).
2. Place the jug on the motor housing (7) and remember to close the lid (2) before each use.
DEVICE DESCRIPTION: BLENDER Ms4080
4 – Gasket 5 – Blade 6 – Plastic nut
10 – Plastic round ring
USEAGE:
1.Place assembled blender on stable, flat surface.
2. Make sure the speed adjustment knob (8) is set to the OFF position.
5. When the blender is in the state of idle operation, e.g. there is no foods in the glass jug, you mustn’t work the appliance for more than
10 seconds to avoid gasket damage.
1. Place the jug upside down on a flat, stable surface. Place the plastic round ring (10) below jug’s threat, then place the gasket (4) on
glass threat and next place the blade (5), then place the plastic nut (6) and turning it in the right side until all parts will be tightly screwed.
place (Picture 3).
3. To disassemble, proceed in the reverse order to assembly.
3. The blender is used to:
ASSEMBLY / DISASSEMBLY
1 – Measurement cup 2 – Lid 3 – Glass jug 1,5 liters
DEVICE OPERATION
4. Do not allow continuous operation of blender for longer than 2 minutes. Later let the device cool down by 1 minute at least.
3. Disassemble in reverse order in relation to assembly.
Before first use:
1. Remove all stickers from the housing, jug and lid of the blender.
6. Overfilling can block the operation, please turn off the unit and pull out the plug, take out some of food, then operating.
2. Place the jug on the motor’s base (7) and remember to cover the lid (2) before each using.
a) blend fruits and vegetables, so before blending, you must cut the food into slices with 10-15mm.
2. Wash the jug and the lid in warm water with washing-up liquid, rinse thoroughly, dry the inside and outside of the jug.
7 – Motor’s housing 8 – Speed adjustment knob 9 – Blue light knob’s illumination