Meridian DSP8000 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 96

Meridian DSP8000 Скачать руководство пользователя страница 14

14

Important safety

instructions

Important safety instructions

Read the instructions.
Keep these instructions.
Follow all instructions.
Do not use this apparatus near water.
Clean only with a dry cloth.
Install only in accordance with the manufacturer’s
instructions.
Refer all servicing to approved service personnel.

This apparatus has been designed with Class 1
construction and must be connected to a mains socket
outlet with a protective earthing connection (the third
grounding pin).

This apparatus uses a single-pole power switch. As
a result it is not isolated from AC mains power when
switched off at the rear panel. The apparatus may
be isolated from mains power either by unplugging
the power connector from the rear of the unit, or by
unplugging the connector at the opposing end of the
power cord or cable from its supply outlet. As a result,
either or both of these connectors should remain
accessible

Safety warnings

WARNING: TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT EXPOSE THIS
APPARATUS TO RAIN OR MOISTURE.

Do not expose the unit to dripping or splashing.
Do not place any object filled with liquid, such as a
vase, on the unit.
Do not place naked flame sources, such as lighted
candles, on the unit.

•
•
•
•
•
•

•

•
•

•

To avoid overheating

Leave at least 10cm around the equipment to ensure
sufficient ventilation.

Do not position the unit:

In direct sunlight.
Near heat sources, such as a radiator.
Directly on top of heat producing equipment, such as
a power amplifier.

To avoid interference

Do not position the unit:

Near strong electrical or magnetic radiation, such as
near a power amplifier.

Radio interference

FCC Warning

: This equipment generates and can

radiate radio frequency energy and if not installed and
used correctly in accordance with our instructions may
cause interference to radio communications or radio
and television reception. It has been type-tested and
complies with the limits set out in Subpart J, Part 1 of
FCC rules for a Class B computing device. These limits
are intended to provide reasonable protection against
such interference in home installations.

EEC

: This product has been designed and type-tested

to comply with the limits set out in EN01 and
EN00.

•

•
•
•

•

«
...
12
13
14
15
16
...
»

Содержание DSP8000

































































































Отзывы:

Нет отзывов