Mercusys MW302R Скачать руководство пользователя страница 103

Страница: 103 / 143

Chapter 7

Company’s server

Router B

Router A

Switch

LAN: 192.168.1.1

192.168.1.100

LAN: 192.168.1.2

WAN: 172.30.30.100

172.30.30.1

POWER

RESET

LAN

WAN

POWER

RESET

LAN

WAN

How can I do that?

Change the routers’ LAN IP addresses to two different IP addresses on the same subnet.
Disable Router B’s DHCP function.

Visit

http://mwlogin.net

, and log in with the password you set for Router A.

Go to

Advanced

Network

Routing

and locate the Static Routing section

Click

Add

and finish the settings according to the following explanations:

• Network Destination

- The destination IP address that you want to assign to a

static route. This IP address cannot be on the same subnet with the WAN IP or
LAN IP of Router A. In the example, the IP address of the company network is the
destination IP address, so here enter 172.30.30.1.

• Subnet Mask

- The Subnet Mask determines which portion of an IP address is the

network portion, and which portion is the host portion.

• Default Gateway

- The IP address of the gateway device to which the data packets

will be sent. This IP address must be on the same subnet with the router’s IP which

Содержание MW302R
















































































































































Результаты поиска

Содержание MW302R

Отзывы:

Похожие инструкции для MW302R

Бренды по названию

Популярные бренды

Mercusys MW302R, Руководство пользователя

Результаты поиска

Содержание MW302R

Отзывы:

Похожие инструкции для MW302R

Бренды по названию

Популярные бренды