manualshive.com logo in svg

Mercury Zeus 3000 Series, Руководство пользователя

Поделиться
Скачать
Mercury Zeus 3000 Series Скачать руководство пользователя страница 55

Section 3 - On the Water

90-866938081   MAY  2009

Page  47

DOCK

Dock mode reduces the percent of throttle throughout the range by 50%. This allows better

control of engine power in close quarter situations.

31464

"DOCK" button

To engage Dock mode:
1. Place both ERC levers in neutral.
2. Press the "DOCK" button located on the DTS trackpad attached to the ERC levers.
3. The "DOCK" button light turns on.
4. Place either ERC lever into gear.
5. The engines raise the RPM at a proportionally lower RPM for the ERC lever position,

and with half the power that is usually available.

To disengage Dock mode:

NOTE: Dock only disengages with the levers in a detent.

1. Bring both ERC levers to forward, neutral, or reverse detent.
2. Press the "DOCK" button. Dock mode disengages and the "DOCK" button light turns

off.

THROTTLE ONLY

To engage Throttle Only mode:
1. Place both ERC levers in neutral.

Содержание Zeus 3000 Series

































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды