background image

GENERAL INFORMATION

10

WHILE BOAT IS STATIONARY

!

 WARNING

Stop your engine immediately whenever anyone in the water is

near your boat. Serious injury to the person in the water is likely

if  contacted  by  a  rotating  propeller,  a  moving  boat,  a  moving

gearcase, or any solid device rigidly attached to a moving boat

or gearcase.

Shift outboard into neutral and shut off the engine before allowing

people to swim or be in the water near your boat.

Wave And Wake Jumping

Operating recreational boats over waves and wake is a natural part

of boating. However, when this activity is done with sufficient speed

to force the boat hull partially or completely out of the water, certain

hazards arise, particularly when the boat re‑enters the water.

14463

The primary concern is the boat changing direction while in the

midst of the jump. In such case the landing may cause the boat to

veer violently in a new direction. Such a sharp change in direction

can cause occupants to be thrown out of their seats, or out of the

boat.

!

 WARNING

Avoid serious injury or death from being thrown within or out of

a boat when it lands after jumping a wave or wake. Avoid wave

or wake jumping whenever possible. Instruct all occupants that

if a wake or wave jump occurs, get low and hang on to any boat

hand hold.

Содержание Air Deck 240









































Отзывы: