Mercury Security © 2014
M5-2K
DOC 10107-0048
REV 1.02
Page 1
www.mercury-security.com
2355 MIRA MAR AVE. LONG BEACH, CA 90815-1755, (562)986-9105 FAX (562) 986-9205
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation.
M5-2K Four Reader Interface Board
Installation and Specifications:
1. General:
Mercury’s M5-2K board for the Micro/PX-2000, Micro/PXN-2000, and MicroPXNplus
®
systems (M2000
enclosure) is part of Mercury Security's bridging hardware technology and provides four reader interface
ports. The M5-2K board accepts data from readers with F/2F, and supervised F/2F signaling and door
hardware. The M5-2K board provides ten inputs (un-supervised/supervised), eight Form-C control relays,
12 Vdc power supply to power readers and other devices.
The M5-IC controller board can be mounted directly on the M5-2K board or in a Micro5
®
enclosure.
If the M5-IC is mounted on the M5-2K board, it is powered by the M5-2K
board’s internal power supply.
Power for the M5-2K board is supplied from an 18 Vac transformer. The M5-2K supports the charging of
an optional 12 Volt, 7 Ah rechargeable sealed lead-acid battery for UPS operation.
This installation manual does not contain the M5-IC controller board configuration information; see
the M5-IC Controller Board Installation and Specifications manual, DOC 10107-0040.
2. Installing the M5-2K Board:
The M5-2K and M5-IC boards replace the current M2000
enclosure’s circuit boards.
M2000 Enclosure with M5-IC and M5-2K
MOUNTING
HOLES 4X
INTERNAL GROUND STUD
2 PLACES
2
6
4
5
3
1
JP1
TB
7
JP2
LO
HI
K8
K7
K6
K5
K4
K3
K2
K1
K8
K7
K6
K5
K4
K3
K2
K1
TB12
TB11
TB10
TB9
J7
TB2
TB1
TB3
TB5
TB4
TB6
ON
S1
3
5
4
2
1
7
8
6
TB
8
VIN
GND
TMPR
PFLT
8
GND
GND
VIN
VIN
TB
1
1
J1
J7
B
T1
B
R
/C
R2325
B
R
/C
R2330
GND
TR-
TR+
TB
2
6
5
4
3
3
1
J4
2
1
4
2
3
S1
1
S2
ON
J6
1
1
10
10
1
1
4
4
1
4
1
4
3
1
8
6
1
6
1
6
1
6
1
1
TB2, PIN 1
INPUTS 6 - 10
TB1, PIN 1
INPUTS 1 - 5
TB5, PIN 1
READER 3
TB3, PIN1
READER 1
TB4, PIN 1
READER 2
TB6, PIN 1
READER 4
M5-2K
STATUS
LEDs
M5-IC
RESET
SWITCH
M5-IC
DIP SWITCHES
M5-IC
STATUS LEDs
M5-2K
DIP SWITCHES
REPLACE CARD
PULLER WITH
MOUNTING SCREWS,
2 EACH
12 VOLT BATTERY
CONNECT TO
CHASSIS GROUND
M5-IC
M5-2K
CONNECT TO EARTH
GROUND HERE
NO CONNECTIONS
ON M5-IC TB1
TB12, PIN 1
K7 & K8 RELAYS
TB11, PIN 1
K5 & K6 RELAYS
TB9, PIN 1
K1 & K2 RELAYS
TB10, PIN 1
K3 & K4 RELAYS
TB7, PIN 1
DOWNSTREAM COMM.
PORT 1, RS-485
JP1, PORT 1 RS-485
TERMINATION
JP2: SET TO LO
TB8, PIN1
POWER CONNECTIONS
