Boleslavova 4, 709 00 Ostrava 9
tel / fax: +420 59 662 70 97
Created: 14.8.2019 , version 1.100en
- 2 -
email: [email protected]
This device is designed for connection to hazardous electric voltages. Ignoring this warning can
result is severe personal injury or mechanical damage. To avoid the risk of electric shock and fire,
the safety instructions of this manual must be obeserved and the guidelines followed.
If the device is used in a manner not specified by the manufacturer, the protection provided by the
device may be impaired.
This device should be installed and adjusted by qualified electrical maintenance personnel familiar
with the connection and operation of the device and the hazards involved. Failure to observe this
precaution could result in injury.
Until the device is fixed, do not connect hazardous voltages to the device - there is a risk of electric
shock.
Before putting the device into operation, this manual must be read carefully and familiarize yourself
with the features of the device and electrical wirrings.
The device is intended exclusively for industrial or professional use.
This device is subject to separate collection, do not dispose of it with municipal waste.
Jaroslav Rzepka MERCOS company is involved in the
collective system
ASEKOL a.s.
(according
to the Waste Act).
Company registration number at the Ministry of Environment is:
00726105-ECZ
.
Jaroslav Rzepka MERCOS company is involved in the
associated performance EKO-KOM
under
client number:
EK-FO6050094
.
The CE mark proves the compliance of the device with the essential requirements of the directives.
1.
R
ECEIPT AND UNPACKING
Before putting the device into operation, please read this manual first and familiarize yourself with the features of the device and
wirrings.
The device does not require any intervention and is capable of operation after unpacking. If the device has been stored
at too low or too high temperatures, it is necessary to let it acclimate for several minutes after unpacking.
2.
M
OUNTING
,
ELECTRICAL WIRRINGS AND OPERATION
This device should be installed and adjusted by qualified electrical maintenance personnel familiar with the connection
and operation of the device, device setup can be done by instructed person.
In case of any doubts, do not hesitate to contact us at :
604 334 327 , [email protected]
Make sure that proper power supply voltage is set and all input and outputs are connected correctly before connection to power
supply system – electrical wirrings diagrams are at the end of this manual.
This device is designed for is continuos run and doesn’t have own power-off switch. Installation must contains some power-off
switch or building distribution circuit-breaker (e.g. power-off switch in switchboard or main distribution circuit-breaker). It has to
be easy accessible by operating staff and has to be marked as cutting-off switch.
3.
M
AINTANANCE
DMP 11 is constructed to require minimal maintainance. Front panel with foil keypad isn’t resistant to organic solvents (e.g.
toluene, acetone etc...).
Use only suitable non-agresive cleaners for cleaning front panel (e.g. industrial alcohol).
To prevent long-term failure-free operation, is recommned to use device in specified temperature range, not expose to extreme
climatic condition, which have effect to longtime lifecycle of electronic components.
4.
R
EPAIR INSTRUCTIONS
Each device was subjected to components quality check control, pre-setting circuits and 24 hours burn-in on power supply. After
24 hours burn-in, pre-set parametres check was made. If device failure occurs (e.g. by overvoltage, mechanical damage, device
malfunction ... ), that impact its own functionality, it is necessary to contact manufacturer, which will provide appropriate repair.
5.
W
ARRANTY
Manafacturer guarantees in accordance with §429 Commercial code (Czech Republic) for technical and operating
characteristics , specified in accompanying technical documentation. Device has 36 months warranty and after warranty service
is provided. This warranty does not apply: (a) to damage caused by accident, abuse, misuse, misapplication; (b) to unauthorized
repair or modification or (c) if serial number has been removed or defaced.
