background image

INSTALLATION

Install the POP-2/4 in the most convenient location for ease of cleaning, maintenance, and general operation. Avoid
installing in locations with drafts, close proximity to grease or vapor-producing appliances, or other high ambient heat
equipment. Allow approximately 1” clearance on sides and back of unit for proper air circulation. Allow sufficient
overhead clearance for proper operation of this unit.

WARNING:
This toaster must be plugged into the proper voltage which is specified on the data plate located on the back
panel of the toaster. Use of any other voltage or altering of the plug or cord may damage the unit, will void the
warranty, and may cause injury.

ELECTRICAL SPECIFICATIONS

SPECIFICATIONS (Standard Models)

VOLTAGES

(VOLTS AC)

AMPERAGE

AMPS

MAX. POWER

(KW)

FREQUENCY

(HZ)

PHASE

CORD

(SUPPLIED)

PLUG

(SUPPLIED)

120

14.8

1.8

50/60

1

3'

NEMA 5-15P

208

9.1

1.9

50/60

1

3'

NEMA 6-15P

220

9.6

2.1

50/60

1

3'

NEMA 6-15P*

240

10.4

2.5

50/60

1

3'

NEMA 6-15P*

  * NOTE: Non- U.S.A. models supplied without plug

The circuit on which the receptacle is installed must be of adequate wiring size and sufficient capacity to meet the
requirements indicated on the unit data plate and in conformance with the National Electrical Code and local electrical
installation codes. Failure to meet these requirenments will void the warranty.

MECHANICAL DIMENSIONS

WARRANTY

The POP-2/4 toaster is guaranteed to be free of defects in material and workmanship for a period of one (1) year from
date of purchase or 18 months from date of shipment from the factory, whichever comes first, provided that the equip-
ment is utilized to the manufacturer’s recommendations and instructions.

The POP-2/4 is warranted on an exchange basis only. 

Please contact our Service Department at 1-800-701-2992

for information.

A warranty registration card is provided with each toaster. Complete all equested information on this card and return to
Merco Savory, Inc. immediately to insure proper warranty registration. Damage resulting from accident, alterations,
misuse, abuse, improper installation or failure to follow use and care instructions will void the warranty.
**The warranty is applicable in the Continental U.S.A. and Hawaii only.

3

Содержание POP-2/4









Отзывы: