background image

P8

Please retain product label and instructions for future reference

             

Step 6

Parts Needed -  No. 11 QTY 1

 

 

    No. 12 QTY 1

 

 

    No. 13 QTY 1

 

 

    No. 14 QTY 1

Arrange the left, right, top & bottom door 

frames 

(No’s. 11, 12, 13 & 14) 

onto a level 

surface. Secure the top and bottom frames to 

the uprights using 2x80mm screw per corner, 

ensuring the screws do 

NOT

 protrude through 

the front of the door framing.

8x80mm Screws

Pre drill 

hole

80mm 

screw

13

14

11

12

IMPORTANT : 

Pre-drill before fixing screws.

The internal lip of the door 

frame should be postioned on 

the inside of the building.

14

12

Step 7

Parts Needed - No. 9 QTY 1

 

 

   No. 10 QTY 1

 

 

   No. 17 QTY 6

             

The Adjustable Door Hinge 

(No.17)

 

comes in three parts. 

Fasten No. 17a into 17b as shown in the 

illustration.

         

Place the master and slave doors 

(No’s 9 & 10)

 onto a flat surface and fix the 

Adjustable door hinge 

(No.17c) 

to the doors 

using 3x30mm screws per hinge.  

Fix 3 x  Adjustable Door Hinges 

(No. 17a & 

b)

 into position onto the door frame using 

4x30mm screws per hinge.

*Ensure the hinges are fitted to the exter-

nal  of the door frame so the doors open 

outwards from the log cabin.

Locate the  doors into the hinges ensuring 

there is equal spacing on each side between 

the doors and door frame, and that the 

doors open & close freely without restric-

tion. 

It is important to fit the doors within the 

frames at this stage so that you can establish 

the position of the hinges. The hinges come 

in three parts. Remove the doors from the 

frame after fitting.

**Ensure to screw into the framing and not 

into the channel.

 

42x30mm  Screws

17a

Pre drill 

hole

30mm 

screw

9

10

17

  a

  b

17b

  a

  b

IMPORTANT : 

Pre-drill before fixing screws.

Slave Door

Master Door

Содержание 0628CSNE0303HGDD2SW-V1


























Отзывы: