Please retain product label and instructions for future reference
For assistance please contact customer care on: 01636 821215
Mercia Garden Products Limited,
Sutton On Trent,
Newark,
Nottinghamshire,
NG23 6QN
www.merciagardenproducts.co.uk
BEFORE YOU START PLEASE READ INSTRUCTIONS CAREFULLY
- Check the pack and make sure you have all the parts listed.
- When you are ready to start, make sure you have the right tools at hand (not supplied) including a Phillips screw-
driver, Stanley knife, Wood saw, Step ladder, Hammer and a Drill with 2mm bit.
- Ensure there is plenty of space and a clean dry area for assembly.
LOCATION FOR YOUR GARDEN BUILDING
A minimum of 60cm should be left around the perimeter of your garden building to allow access for maintenance,
annual treatment and to allow air flow around the building.
Where possible you should avoid placing your garden building underneath large trees to prevent the tree causing
damage to the building.
TIMBER
As with all natural materials, timber can be affected during various weather conditions. For the duration of heavy
or extended periods of rain, swelling of the wood panels may occur. Warping of the wood may also occur during
excessive dry spells due to an interior moisture loss. Unfortunately, these processes cannot be avoided but can be
helped. It is suggested that the outdoor building is sprayed with water during extended periods of warm sunshine
and sheltered as much as possible during rain or snow.
Once your garden building has been installed it will need to be treated as soon as possible and annually to prevent
the timber from deteriorating and to waterproof it. This is required to maintain the anti-rot guarantee.
Dip Treated buildings - Require a preservative treatment to protect against rot and decay and a waterproof treat-
ment to prevent water ingress
Pressure Treated buildings - Require a waterproof treatment to prevent water ingress
Log Cabins - Are supplied untreated and require a preservative and waterproofing treatment.
BUILDING A BASE
When thinking about where the building and base is going to be constructed:
Ensure that there will be access to all sides for maintenance work and annual
treatment.
Ensure the base is level and is built on firm ground, to prevent distortion. Refer to diagrams for the base
dimensions, The base should be slightly smaller than the external measurement of the building, i.e. The cladding
should overlap the base, creating a run off for water. It is also recommended that the floor be at least 25mm above
the surrounding ground level to avoid flooding.
TYPES OF BASE
- Concrete 75mm laid on top of 75mm hard-core.
- Slabs laid on 50mm of sharp sand.
Whilst all products manufactured are made to the highest standards of Safety and in the case of childrens
products independently tested to EN71 level, we cannot accept responsibility for your safety whilst erecting or
using this product.
Turn Button - QTY 2
PI-07-0034
34
P 5
Building content - Pack B
01DTPRMSHAX0210NWPB-V1
Building content - Pack C
01DTPRMSHAX0510OPPB-V1
Building content - Pack D
01DTPRMSHAX0510SDPB-V1
Plain Side Panel
AI-S21SHPPTF596X1784-V1
QTY 2
2ft Roof
AI-S21MBOHAR596X1760-V1
QTY 2
2ft Floor
AI-S21MBF1529X596-V1
QTY 2
Single Door Panel
AI-01S21SHSD1490x1784-V1
QTY 1
5ft Floor Panel
AI-S21MBF1529X1485-V2
QTY 2
5ft Roof Panel
AI-S21MBOHAR1490X1760-V1
QTY 2
36
37
38
39
35
40
Pad Bolt
PI-07-0035
Truss Brace - 27x44x1700mm - QTY 2
F2744-G-1740mm
Truss Block - 44x44x140mm - QTY 2
F4444-G-160mm
Truss Support Triangle - 12x503mm - QTY 2
MB12-P-503mm
11
19
22
24
14
Truss Support -
AI-S22HAXT1651X88-V1
- QTY 2
Cover Strip - 12x56x1774mm - QTY 2
S1256-1774mm
27
U Channel - QTY 2
PI-07-0013
2
1
Plain Panel
AI-S21SHPPTF1490X1784-V1
QTY 1
Window Side Panel
AI-01S21SH1LFW1490X1784-V1
QTY 1
Window
AI-FW1000X540-V1
QTY 1
10
Truss Brace - 27x44x1700mm - QTY 2
F2744-G-1740mm
Truss Block - 44x44x140mm - QTY 2
F4444-G-160mm
Truss Support Triangle - 12x503mm - QTY 2
MB12-P-503mm
11
19
22
24
14
Truss Support -
AI-S22HAXT1651X88-V1
- QTY 2
Cover Strip - 12x56x1774mm - QTY 2
S1256-1774mm
Window Strip - 12x56x1038mm - QTY 1
S1256-1038mm
13
27
U Channel - QTY 2
PI-07-0013
Casement stay - QTY 1
PI-07-0007
Butt Hinge - QTY 2
PI-07-0066
30
26
5ft Floor Panel
AI-S21MBF1529X1485-V2
QTY 2
2
Plain Panel
AI-S21SHPPTF1490X1784-V1
QTY 1
5ft Roof Panel
AI-S21MBOHAR1490X1760
QTY 2
38
6
Door
AI-S21FBMBZBD600X1720-V1
QTY 2
Truss Brace - 27x44x1700mm - QTY 2
F2744-G-1740mm
Truss Block - 44x44x140mm - QTY 2
F4444-G-160mm
Truss Support Triangle - 12x503mm - QTY 2
MB12-P-503mm
11
19
22
24
14
Truss Support -
AI-S22HAXT1651X88-V1
- QTY 2
Cover Strip - 12x56x1774mm - QTY 2
S1256-1774mm
Door Beading Strip - 12x30x1600mm - QTY 2
S1230-1600mm
12
28
T Hinge - QTY 3
PI-07-0021
27
U Channel - QTY 2
PI-07-0013
Door Block - 27x44x150mm - QTY 1
F2744-150mm
20
5
5
17
Floor Block - 27x44x400mm - QTY 2
F2744-400mm
17
Floor Block - 27x44x400mm - QTY 5
F2744-400mm
17
Floor Block - 27x44x400mm - QTY 5
F2744-400mm
Nail Bag
30mm Screw x 34
50mm Screw x 12
70mm Screw x 4
40mm Screw x 40
100mm Screw x 2
There may be extra screws present in the nail bag
Nail Bag
There may be extra screws present in the nail bag
Nail Bag
There may be extra screws present in the nail bag
Felt Tacks x 35
30mm Screw x 43
50mm Screw x 16
70mm Screw x 4
40mm Screw x 56
100mm Screw x 2
Felt Tacks x 75
16mm Screws x 6
30mm Screw x 54
50mm Screw x 16
70mm Screw x 4
40mm Screw x 56
100mm Screw x 2
Felt Tacks x 75
Содержание 01DTPRMSHAX1010DDOP-V1
Страница 28: ... 2 1 3 4 ...
Страница 29: ... 1 2 ...