X
Point garage door remote control
A
towards buttons
;
to
?
on the rear-view
mirror at a distance of 5 to 20 cm.
i
The required distance between remote
control
A
and the integrated garage door
opener depends on the garage door drive
system. You might require several
attempts. You should test every position for
at least 25 seconds before trying another
position.
X
Press and hold button
B
on remote control
A
until indicator lamp
:
lights up green.
If indicator lamp
:
lights up green or
flashes, then programming has been suc-
cessful.
X
Release button
;
,
=
or
?
on the inte-
grated garage door opener and button
B
on garage door remote control
A
.
If indicator lamp
:
lights up red:
X
Repeat the programming procedure for the
corresponding button on the rear-view mir-
ror. When doing so, vary the distance
between remote control
A
and the rear-
view mirror.
i
If the indicator lamp flashes green after
successful programming, the garage door
system is using a rolling code. After pro-
gramming, you must synchronise the
garage door opener integrated in the rear-
view mirror with the receiver of the garage
door system.
Synchronising the rolling code
Your vehicle must be within reach of the
garage door or exterior gate drive. Make sure
that neither your vehicle nor any persons/
objects are present within the sweep of the
door or gate.
Observe the safety notes when performing
the rolling code synchronisation
(
Y
page 243).
X
Turn the key to position 2 in the ignition
lock.
X
Press the programming button of the door
or gate drive (see the door or gate drive
operating instructions, e.g. under "Pro-
gramming of additional remote controls").
i
Usually, you now have 30seconds to ini-
tiate the next step.
X
Press previously programmed button
;
,
=
or
?
of the integrated garage door
opener until the door starts to move.
The rolling code synchronisation is then
complete.
Problems when programming
If you have problems when programming the
integrated garage door opener, please note
the following:
R
Check the transmitter frequency of garage
door drive remote control
A
. This can usu-
ally be found on the back of the remote
control.
R
Change the batteries in garage door remote
control
A
. This increases the likelihood
that remote control
A
will send a strong
and precise signal to the integrated garage
door opener.
R
When programming, hold remote control
A
at varying distances and angles from the
button that you are programming. Try vari-
ous angles at a distance of between
5 and 30 cm or at the same angle but at
varying distances.
R
If there is another remote control for the
same garage door drive, perform the pro-
gramming steps again using this remote
control. Before performing these steps,
make sure that new batteries have been
fitted in garage door drive remote control
A
.
R
Note that some remote controls transmit
only for a limited period (the indicator lamp
on the remote control goes out). Press but-
244
Features
Stowing
and
features
Содержание SLK 2012
