manualshive.com logo in svg

Menumaster DECS11MA, Руководство по обслуживанию

Поделиться
Скачать
Menumaster DECS11MA Скачать руководство пользователя страница 24

5-8

CAUTIONS

1. DISCONNECT THE POWER SUPPLY CORD FROM THE OUTLET WHENEVER REMOVING THE

OUTER CASE FROM THE UNIT. PROCEED WITH THE TEST ONLY AFTER DISCHARGING THE HIGH
VOLTAGE CAPACITOR AND REMOVING THE WIRE LEADS FROM THE PRIMARY WINDING OF THE
HIGH VOLTAGE TRANSFORMER. (SEE PAGE 2-1)

2. ALL OPERATIONAL CHECKS WITH MICROWAVE ENERGY MUST BE DONE WITH A LOAD (1 LITER

OF WATER IN CONTAINER) IN THE OVEN.

COMPONENTS

TEST PROCEDURE

RESULTS

HIGH VOLTAGE
TRANSFORMER
(Wire leads removed)

MAGNETRON
(Wire leads removed)

1. Measure the resistance. 

(Ohm-meter scale: Rx1 and Rx100)
•  Primary winding
•  Secondary winding
•  Filament winding

2. Measure the resistance. 

(Ohm-meter scale: Rx1000) 
• Primary winding to ground 
• Filament winding to ground

1. Measure the resistance. 

(Ohm-meter scale: Rx1)
• Filament terminal

2. Measure the resistance.

(Ohm-meter scale: Rx1000) 
• Filament to chassis

Approx.: 1.81 ~ 2.4 ohm
Approx.: 110 ~ 125 ohm
Less than: 1 ohm

Normal: Infinite
Normal: Infinite

Normal: Less than 1 ohm

Normal: Infinite

FILAMENT
WINDING

SECONDARY
TERMINAL

 PRIMARY
TERMINAL

COMPONENT TEST PROCEDURE

Содержание DECS11MA













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды