Memorex MVT2139 A Series, Руководство по обслуживанию

Страница: 29 / 68

D2-3
MECHANICAL ADJUSTMENTS
2-3: 2-2:
When the Tape Running Mechanism does not work well,
adjust the following items.
CONFIRMATION AND ADJUSTMENT OF AUDIO/
CONTROL HEAD
1.
2.
3.
4.
When the height is not correct, turn the screw (3) to
adjust the height. Then, adjust the 1~3 again.
Playback the VHS Alignment Tape (JG001 or JG001B).
(Refer to SERVICING FIXTURE AND TOOLS)
Confirm that the reflected picture of stamp mark is
appeared on the tape prior to P4 Post as shown in Fig.
2-2-A.
a)
b)
Turn the screw (2) to set the audio level to maximum.
Confirm that the bottom of the Audio/ Control Head and
the bottom of the tape is shown in Fig. 2-2-C.
c)
When the reflected picture is distorted, turn the screw
(1) clockwise until the distortion is disappeared.
When the reflected picture is not distorted, turn the
screw (1) counterclockwise until little distortion is
appeared, then adjust the a).
P4 Post
Fig. 2-2-A
Audio/Control Head
(1)
(3)
(2)
Fig. 2-2-B
Audio/Control Head
Fig. 2-2-C
TAPE RUNNING ADJUSTMENT
(X VALUE ADJUSTMENT)
Confirm and adjust the height of the Reel Disk.
(Refer to item 1-1)
Confirm and adjust the position of the Tension Post. (Refer
to item 1-2)
Adjust the Guide Roller. (Refer to item 2-1)
Confirm and adjust the Audio/Control Head.
(Refer to item 2-2)
Connect CH-1 of the oscilloscope to TP4001, CH-2 to
TP1002 and CH-3 to HOT side of Audio Out Jack.
Playback the VHS Alignment Tape (JG001S or JG001T).
(Refer to SERVICING FIXTURE AND TOOLS)
Press and hold the Tracking-Auto button on the remote
control more than 2 seconds to set tracking to center.
Set the X Value adjustment driver (JG153) to the (4) of
Fig. 2-2-B. Adjust X value so that the envelope waveform
output becomes maximum. Check if the relation between
Audio and Envelope waveform becomes (1) or (2) of
Fig. 2-3. 1.
2.
3.
4.
5.
6.
7.
8.
(4)
Audio/Control Head
Reflected picture of
Stamp Mark
Stamp Mark
Tape
0.25
±
0.05mm
Envelope
CH-3
Audio
(1)
(2)
Fig. 2-3
2-4: CONFIRM HI-FI AUDIO (Hi-Fi model only)
Connect CH-1 of the oscilloscope to TP4001 and CH-2 to
the Hi-Fi Audio Out Jack.
Playback the VHS Alignment Tape (JG001P or JG001Q).
(Refer to SERVICING FIXTURE AND TOOLS)
Press and hold the Tracking-Auto button on the remote
control more than 2 seconds to set tracking to center.
Press the Tracking Up button and count number of steps
which the audio output is changed from Hi-Fi (10KHz) to
MONO (6KHz).
Press and hold the Tracking-Auto button on the remote
control more than 2 seconds to set tracking to center.
Press the Tracking Down button and count number of
steps which the audio output is changed from Hi-Fi
(10KHz) to MONO (6KHz).
If the difference are more than 3 steps, set the X Value
adjustment driver (JG153) to 4 of Fig. 2-2-B. Change the
X Value and adjust it so that the value becomes within 2
steps. 1.
2.
3.
4.
5.
6.
7.