Memmert CTC 256 Скачать руководство пользователя страница 6

Страница: 6 / 68

Safety regulations

1.1 Terms and symbols used

In this manual, certain common terms and symbols are used to warn you of dangers or to

give you hints that are important in avoiding injury or damage. Observe and follow these

hints and regulations to avoid accidents and damage. These terms and symbols are explained

below.

1.1.1 Terms used

„Warning“

is used whenever you or somebody else could be injured if you do not

observe the accompanying safety regulation.

„Caution“

is used for information that is important for avoiding damage.

1.1.2 Symbols used

Prohibition sign (forbidding an action)

Do not tilt

appliance

Do not lift

appliance

Do not stack

appliance

Warning symbols (warning of a danger)

Danger of

electric shock

Explosive

atmosphere

Cold/danger of

frostbite

Heat/hot surface/

danger of

burning

Danger of hot

vapours/scalding

Dangerous

gases/vapours

Regulation signs (stipulate an action)

Disconnect the

mains plug

Wear gloves

Wear safety

shoes

Observe information in separate manual

Other symbols

Information on

first aid

Important or useful additional information

Содержание CTC 256





































































Результаты поиска

Содержание CTC 256

Отзывы:

Похожие инструкции для CTC 256

Бренды по названию

Популярные бренды

Memmert CTC 256, Руководство по эксплуатации

Результаты поиска

Содержание CTC 256

Отзывы:

Похожие инструкции для CTC 256

Бренды по названию

Популярные бренды