Meltem M-WRG-K Скачать руководство пользователя страница 10

Страница: 10 / 15

M-WRG-K

Installation manual

M-WRG-S

Meltem Wärmerückgewinnung GmbH & Co.KG

Am Hartholz 4 D-82239 Alling [email protected] www.meltem.com

3.8. Install the power cable

•

Install a power cable, size 3x1,5 mm

or NYM,

excess length of aprox.250mm

•

With the units

M-WRG-S/Z-A, M-WRG-S/Z-EIB,
M-WRG-S/Z-24 , M-WRG-S 485,
M-WRG-S 485-TF, M-WRG-S 485-TFC
an additional control cable needs to be installed.
excess length of aprox.250mm

3.9. Resurfacing

•

Caution!

Before resurfacing, ensure that the ventilation pipes

are covered!

•

Resurface and reseal the wall

•

Wait for plaster to dry

3.10. Trim ventilation pipes

•

Cut the ventilation pipes

on the

inside

so they are level with the wall

•

Smooth out any rough edges, deburr

•

Cut and deburr the ventilation pipes on the

outside

depending on the façade covers:

Facade cover model

Excess length of ventilation
pipes

Ventilation hood
M-WRG-ES

5-10mm

Ventilation Grille-Set
M-WRG-ESR

25-30mm

Ventilation Grille (AP)
M-WRG-ESG/AP

5mm

Содержание M-WRG-K
















Результаты поиска

Содержание M-WRG-K

Отзывы:

Бренды по названию

Популярные бренды

Meltem M-WRG-K, Руководство по установке

Результаты поиска

Содержание M-WRG-K

Отзывы:

Бренды по названию

Популярные бренды